Nissan Sentra. Instruction — part 657
MWI-74
< SYMPTOM DIAGNOSIS >
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000009758311
• The displayed outside air temperature is higher than the actual temperature.
• The displayed outside air temperature is lower than the actual temperature.
• Outside air temperature is not indicated.
Diagnosis Procedure
INFOID:0000000009758312
1.
CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK AMBIENT SENSOR
Check the ambient sensor. Refer to
MWI-62, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
NO
>> Replace ambient sensor. Refer to
MWI
THE LOW WASHER FLUID WARNING LAMP DOES NOT TURN ON OR OFF
MWI-75
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LOW WASHER FLUID WARNING LAMP DOES NOT TURN ON OR
OFF
Description
INFOID:0000000009758313
• The low washer fluid warning lamp is still illuminated even after washer fluid is added.
• The low washer fluid warning lamp is not illuminated even though the washer tank is empty.
Diagnosis Procedure
INFOID:0000000009758314
1.
CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT
Check the washer fluid level switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK WASHER FLUID LEVEL SWITCH
Check for the washer fluid level switch. Refer to
MWI-65, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-77, "Removal and Installation"
NO
>> Replace washer fluid level switch. Refer to
WW-53, "Removal and Installation"
.
MWI-76
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
COMPASS
COMPASS : Description
INFOID:0000000010288795
COMPASS
• The electronic compass is highly protected from changes in most magnetic fields. However, some large
changes in magnetic fields can affect it. Some examples are (but not limited to): high tension power lines,
large steel buildings, subways, steel bridges, automatic car washes, large piles of scrap metal, etc. While
this does not happen very often, it is possible.
• During normal operation, the Compass Mirror will continuously update the compass calibration to adjust for
gradual changes in the vehicle's magnetic "remnant" field. If the vehicle is subjected to high magnetic influ-
ences, the compass may appear to indicate false headings, become locked, or appear that it is unable to be
calibrated. If this occurs, perform the calibration procedure.
• If at any time the compass continually displays the incorrect direction or the reading is erratic or locked, ver-
ify the correct zone variance.
Symptom Chart
Symptom
Cause
Solution / Reference
The compass display reads "C".
• Compass is not calibrated.
• Incorrect zone variance setting.
• Large change in magnetic field (Steel
bridges, subways, concentrations of
metal, car washes, etc.)
• Compass was calibrated incorrectly or
in the presence of a strong magnetic
field.
Perform Calibration. Refer to
"COMPASS : System Description"
.
Compass shows the wrong direction.
Compass does not change direction ap-
pears "Locked".
Compass does not show all the directions,
one or more is missing.
The compass was calibrated but it "loses"
calibration.
On long trips the compass shows the
wrong direction.
Perform Zone Variation Setting if correct
reading is desired in that location. Refer to
MWI
COMBINATION METER
MWI-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
COMBINATION METER
Exploded View
INFOID:0000000009758315
Removal and Installation
INFOID:0000000009758316
REMOVAL
1. Remove cluster lid A. Refer to
IP-19, "Removal and Installation"
2. Remove the screws from the combination meter.
3. Remove the combination meter.
4. Disconnect the combination meter harness connector and remove.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000009758317
DISASSEMBLY
CAUTION:
• Do not touch the display, pointer, the inside of front cover and the printed area of the dial during the
work.
• Keep away from magnetic sources.
1.
Combination meter
2.
Front cover
JSNIA5053ZZ
JSNIA5054ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст