Nissan Sentra. Instruction — part 256
DLK-140
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK OPERATION WARNING DOES NOT OPERATE
DOOR LOCK OPERATION WARNING DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009756458
1.
CHECK DOOR LOCK FUNCTION
Check door lock function.
Does door lock/unlock using door request switch?
YES
>> GO TO 2.
NO
>> Refer to
DLK-121, "Diagnosis Procedure"
.
2.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
DLK-91, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-73, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
KEY ID WARNING DOES NOT OPERATE
DLK-141
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY ID WARNING DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009756459
1.
CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis relevant to DTC indicated.
2.
CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Perform trouble diagnosis relevant to DTC indicated.
3.
CHECK INTELLIGENT KEY
Check Intelligent Key.
DLK-106, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
.
• Trunk room: Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK KEY WARNING LAMP
Check key warning lamp.
DLK-107, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1. Replace BCM. Refer to
BCS-73, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
DLK-142
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
PANIC ALARM FUNCTION DOES NOT OPERATE
PANIC ALARM FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009756460
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-124, "Diagnosis Procedure"
.
2.
CHECK HORN OPERATION
1. Select IPDM E/R using CONSULT.
2. Select HORN in ACTIVE TEST mode.
3. Touch On to check that it works normally.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK PANIC ALARM SET SETTING IN WORK SUPPORT
1. Select INTELLIGENT KEY of BCM.
2. Select PANIC ALARM SET in WORK SUPPORT mode.
3. Check PANIC ALARM SET setting in WORK SUPPORT.
BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set MODE 1 or MODE 3 in PANIC ALARM SET
4.
REPLACE BCM
1. Replace BCM. Refer to
BCS-73, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
SQUEAK AND RATTLE TROUBLE DIAGNOSES
DLK-143
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work Flow
INFOID:0000000010291104
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to
DLK-147, "Diagnostic Worksheet"
. This information is necessary to duplicate
the conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain
all the facts and conditions that exist when the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer is
concerned about. This can be accomplished by test driving the vehicle with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping.
• Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
• Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
• Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending upon the person. A noise that you may judge
as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperature, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
SBT842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст