Nissan Sentra. Instruction — part 805
B0021 SIDE CURTAIN AIR BAG MODULE LH
SRC-55
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-39, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-39, "Intermittent Incident"
.
5.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
SIDE CURTAIN AIR BAG MODULE LH
1. Replace the side curtain air bag module LH. Refer to
SR-22, "Removal and Installation"
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
SRC-56
< DTC/CIRCUIT DIAGNOSIS >
B0021 SIDE CURTAIN AIR BAG MODULE LH
>> END
B0028 SIDE AIRBAG MODULE RH
SRC-57
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B0028 SIDE AIRBAG MODULE RH
Description
INFOID:0000000009757967
DTC B0028 FRONT RH SIDE AIR BAG MODULE
The front RH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the front RH side air bag module.
PART LOCATION
SRC-5, "Component Parts Location"
.
DTC Logic
INFOID:0000000009757968
DTC DETECTION LOGIC
With CONSULT
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check for DTC using CONSULT.
Is the DTC detected?
YES (Current DTC)>>Refer to
YES (Past DTC)>>GO TO 2.
NO
>> Inspection End.
2.
ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased?
YES
>> Inspection End.
NO
>> Refer to
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.
CHECK SELF-DIAG RESULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-17, "Trouble Diagnosis without CONSULT"
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?
YES
>> Refer to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009757969
1.
HARNESS CONNECTOR
CONSULT name
DTC
DTC detecting condition
Repair order
SIDE AIRBAG MODULE RH CIRCUIT
[OPEN]
B0028
Front RH side air bag module circuit is
open.
SIDE AIRBAG MODULE RH CIRCUIT
[VB-SHORT]
Front RH side air bag module circuit is
shorted to a power supply circuit.
SIDE AIRBAG MODULE RH CIRCUIT
[GND-SHORT]
Front RH side air bag module circuit is
shorted to ground.
SIDE AIRBAG MODULE RH CIRCUIT
[SHORT]
Front RH side air bag module circuits
are shorted to each other.
SRC-58
< DTC/CIRCUIT DIAGNOSIS >
B0028 SIDE AIRBAG MODULE RH
Visually inspect all applicable harness connectors for the following:
• Visible damage to connector or terminal
• Loose terminal
• Poor connection
NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform one of the following repairs:
• Visible damage: Replace the harness.
• Loose terminal: Secure the terminal.
• Poor connection: Secure the connection.
2.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 3.
NO
>> Refer to
GI-39, "Intermittent Incident"
.
3.
WIRING HARNESS
Check the wiring harness for visible damage.
NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace the harness.
4.
CONFIRM DTC
1. Reconnect all harness connectors.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 5.
NO
>> Refer to
GI-39, "Intermittent Incident"
.
5.
AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace the air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 6.
NO
>> Clear DTC. Inspection End.
6.
SIDE AIR BAG MODULE RH
1. Replace the side air bag module RH. Refer to
SR-24, "Removal and Installation"
.
2. Turn ignition switch ON.
3. Check for DTC using CONSULT.
Is DTC still current?
YES
>> GO TO 7.
NO
>> Clear DTC. Inspection End.
7.
RELATED HARNESS
Replace the related harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст