Nissan Qashqai (2007-2010). Manual — part 1292

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicles in.

>> GO TO 2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

PERFORM "BASIC INSPECTION"

Perform the basic inspection.
Refer to

RF-49, "Basic Inspection"

>> GO TO 4.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2. Then identify where to start perform-
ing the diagnosis based on possible causes and symptom.

>> GO TO 5.

IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”

Perform the diagnosis with “Component diagnosis” of the applicable system.

>> GO TO 6.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 7.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Is the malfunction repaired or replaced?

YES

>> Trouble diagnosis is completed.

>> GO TO 3.

RF-4

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000000984257

Initial setting is necessary when battery terminal is removed and replacing sunshade motor assembly.
NOTE:
The following specified operations are not performed under the non-initialized condition.
• Auto-slide operation
• Anti-pinch function

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000000978378

INITIALIZATION PROCEDURE

If the sunshade does not close or open automatically, use the following procedure to return sunshade opera-
tion to normal.
1.

Return sunshade to closed position.

Release the close switch once, press the close switch again, keep pushing the switch until shade is fully
closed. (About 30 seconds)

Release the switch again, and push the close switch within the first 10 seconds. (keep pushing the switch)

After 3 or 4 seconds, the shade will be automatically operated in sequence of slide open and slide close.
After the shade stops, release the switch 0.5 second later.

If sunshade switch operates normally, this initialization is done.

ANTI-PINCH FUNCTION

Full open the shade.

Place a piece of wood near fully closed position.

Close the shade completely with auto-slide close.

Check that shade opens fully and stops.

CAUTION:

• Perform initialization procedure setting when auto-slide operation or anti-pinch function does not

operate normally.

• Check that auto-slide operates before inspection when system initialization is performed.
• Do not check with hands and other part of body because they may be pinched. Do not get pinched.
• Depending on environment and driving conditions, if a similar impact or load is applied to the sun-

shade it may open.

• Thermal cut out may occur if open/close operation is performed continuously. In this situation allow

system to cool before re-use.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000000984258

Refer to

RF-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description"

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000000978147

Refer to

RF-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

for initialization procedure and check anti-pinch function.

SUNSHADE SYSTEM

RF-5

< FUNCTION DIAGNOSIS >

FUNCTION DIAGNOSIS

SUNSHADE SYSTEM

System Diagram

INFOID:0000000000978148

SUNSHADE SYSTEM

System Description

INFOID:0000000000978149

SUNSHADE SYSTEM

INPUT/OUTPUT SIGNAL CHART

SUNSHADE OPERATION

• Sunshade motor assembly operates with the power supply from BCM while ignition switch is ON.
• Slide open and slide close signals from sunshade switch enables to operate sunshade motor.

AUTO OPERATION

Sunshade AUTO feature makes it possible to slide open and slide close the sunshade without holding the sun-
shade switch at the slide open or slide close position.
Auto operation is activated by a short press.(Less than 0.7 second)

ANTI-PINCH FUNCTION

The CPU of sunshade motor assembly monitors the sunshade motor operation and the shade position (fully-
closed or other) by the signals from sunshade motor assembly.
When sunshade motor detects an interruption during the slide close operation, sunshade will auto open to the
full-open position.
• Close operation when ignition switch is in the “ON” position

Component Parts Location

INFOID:0000000000978150

JMKIA0303GB

Item

Input signal to sunshade motor assembly

Sunshade motor function

Actuator

Sunshade switch

Sunshade switch signal (slide open)

Sunshade control

Sunshade motor

Sunshade switch signal (slide close)

Была ли эта страница вам полезна?

Да!Нет

Nissan Qashqai (2007-2010). Manual — part 1292

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.