Nissan Qashqai (2007-2010). Manual — part 620
PREPARATION
DLN-53
< PREPARATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ST01530000
Drift
a:
φ
48 mm (1.89 in) dia.
b:
φ
41 mm (1.61 in) dia.
Installing ring gear
ST35272000
Drift
a:
φ
72 mm (2.83 in) dia.
b:
φ
40 mm (1.57 in) dia.
c:
φ
35.5 mm (1.398 in) dia.
• Installing ring gear
• Installing outer race of drive pinion bearing
(front side)
KV10111400
Drift
a:
φ
25 mm (0.98 in) dia.
b:
φ
20.8 mm (0.819 in) dia.
Installing inner race of ring gear shaft bearing
(transfer case side)
KV381054S0
Puller
Removing drive pinion oil seal
ST23860000
Drift
a:
φ
38 mm (1.50 in) dia.
b:
φ
33 mm (1.30 in) dia.
Installing inner race of drive pinion bearing
(front side)
ST3127S000
Preload gauge
Measuring preload torque
Tool number
Tool name
Description
ZZA0534D
NT107
ZZA1003D
ZZA0601D
ZZA0534D
ZZA0503D
DLN-54
< PREPARATION >
[TRANSFER: TY30A]
PREPARATION
CVT : Commercial Service Tools
INFOID:0000000001115036
ST38280000
Bushing remover
Installing outer race of drive pinion bearing
(front side)
ST33230000
Drift
a:
φ
51 mm (2.01 in) dia.
Installing outer race of drive pinion bearing
(rear side)
Tool number
Tool name
Description
NT685
ZZA0938D
Tool name
Description
Drift
a:
φ
12 mm (0.47 in) dia.
b:
φ
18 mm (0.71 in) dia.
Removing inner race of ring gear shaft bear-
ing (transfer case side)
Drift
a:
φ
49 mm (1.93 in) dia.
b:
φ
67 mm (2.64 in) dia.
Removing inner race of ring gear shaft bear-
ing (adapter case side)
Drift
a:
φ
57 mm (2.24 in) dia.
b:
φ
47 mm (1.85 in) dia.
Installing inner race of ring gear shaft bearing
(adapter case side)
ZZA1178D
NT660
ZZA1003D
TRANSFER OIL
DLN-55
< ON-VEHICLE MAINTENANCE >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ON-VEHICLE MAINTENANCE
TRANSFER OIL
Inspection
INFOID:0000000000972126
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case, etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug (1) and gasket. Then check that oil is filled up
(A) from mounting hole for the filler plug.
2.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
(M/T models),
(CVT models).
CAUTION:
Never reuse gaskets.
Draining
INFOID:0000000000972127
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the engine and remove drain plug (1) and gaskets to drain
the transfer oil.
CAUTION:
Never remove tooth contact test hole plug (2).
3.
Before installing drain plug, set a new gasket. Install drain plug
on transfer and tighten to the specified torque. Refer to
(M/T models),
(CVT models).
CAUTION:
Never reuse gaskets.
Refilling
INFOID:0000000000972128
1.
Remove filler plug (1) and gasket. Then fill oil up to mounting
hole (A) for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2.
Leave the vehicle for 3 minutes. Then check oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
(CVT models).
CAUTION:
Never reuse gasket.
SDIA3060J
SDIA3059J
Oil grade and Viscosity
: Refer to
.
Oil capacity
: Refer to
.
SDIA3060J
DLN-56
< ON-VEHICLE REPAIR >
[TRANSFER: TY30A]
4WD CONTROL UNIT
ON-VEHICLE REPAIR
4WD CONTROL UNIT
LHD
LHD : Exploded View
INFOID:0000000001083044
LHD : Removal and Installation
INFOID:0000000001083045
REMOVAL
1.
Remove the instrument assist lower panel. Refer to
.
2.
Disconnect 4WD control unit harness connector.
3.
Remove 4WD control unit (1) mounting screws.
4.
Remove 4WD control unit.
INSTALLATION
Install is the reverse order of removal.
RHD
RHD : Exploded View
INFOID:0000000000972129
1.
4WD control unit
: Vehicle front
JSDIA0224ZZ
JSDIA0225ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст