Nissan Qashqai (2007-2010). Manual — part 1406
FRONT FOG LAMP
EXL-329
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000001099392
Removal and Installation
INFOID:0000000001099393
REMOVAL
1.
Remove the inner fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp connector.
3.
Remove the screw. Remove the front fog lamp.
4.
Remove the clip. Remove the front fog lamp bracket.
INSTALLATION
Installation is the reverse order of removal.
Replacement
INFOID:0000000001099394
CAUTION:
Disconnect the battery negative terminal or the fuse.
1.
Remove the fender protector. Keep the service area.
2.
Remove the front fog lamp bulb connector (1).
3.
Rotate the bulb (2) counterclockwise and unlock it.
1.
Front fog lamp bracket
2.
Front fog lamp
JPLIA0251ZZ
JPLIA0252ZZ
EXL-330
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
LIGHT & RAIN SENSOR
LIGHT & RAIN SENSOR
Exploded View
INFOID:0000000001099396
CAUTION:
• When the light & rain sensor is removed from windshield, gel/adhesive part of housing should not be
re-used.
• When re-using the light & rain sensor (i.e. after windshield replacement), replace the light & rain sen-
sor housing.
REMOVAL
DISASSEMBLY
CAUTION:
Never touch the electronic circuit board.
Removal and Installation
INFOID:0000000001099397
1.
Light & rain sensor connector
2.
Light & rain senor
3.
Inside mirror cover (lower)
4.
Inside mirror cover (upper)
A.
Metal spring clip
JPLIA0301ZZ
1.
Light & rain senor housing
2.
Light & rain senor
A.
Pawl
Refer to
for symbols not described above.
JSLIA0096ZZ
LIGHT & RAIN SENSOR
EXL-331
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
CAUTION:
• When the light & rain sensor is removed from windshield, gel/adhesive part of housing should not be
re-used.
• When re-using the light & rain sensor (i.e. after windshield replacement), replace the light & rain sen-
sor housing.
REMOVAL
1.
Remove the inside mirror cover (upper and lower). Refer to
.
2.
Disengage the both sides of metal spring clips, and remove the light & rain sensor from the windshield.
3.
Disconnect light & rain sensor connector.
NOTE:
When replacing the light & rain sensor housing;
Disengage the pawls, and remove the light & rain sensor housing from the light & rain sensor.
CAUTION:
Never touch the electronic circuit board.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Surface of windshield should be cleaned.
• Never touch gel/adhesive of new part.
EXL-332
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Exploded View
INFOID:0000000001099398
Removal and Installation
INFOID:0000000001099399
REMOVAL
1.
Remove steering column cover. Refer to
.
2.
While pressing pawls, pull the light & turn signal switch. And disconnect from the switch base.
INSTALLATION
Installation is the reverse order of removal.
1.
Light & turn signal switch
A.
Pawl
JSLIA0092ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст