Nissan Qashqai (2007-2010). Manual — part 402
P1217 ENGINE OVER TEMPERATURE
EC-1127
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Without CONSULT-III
1.
Start engine and let it idle.
2.
Turn air conditioner switch ON.
3.
Turn blower fan switch ON.
4.
Make sure that cooling fan operates at low speed.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Check cooling fan low speed control circuit.
5.
CHECK COOLING FAN HIGH SPEED OPERATION
Without CONSULT-III
1.
Turn ignition switch OFF.
2.
Turn air conditioner switch and blower fan switch OFF.
3.
Disconnect engine coolant temperature sensor harness connector.
4.
Connect 150
Ω
resistor to engine coolant temperature sensor harness connector.
5.
Restart engine and make sure that cooling fan operates at higher speed than low speed.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Check cooling fan high speed control circuit.
6.
CHECK COOLING SYSTEM FOR LEAK
Check cooling system for leak. Refer to
.
Is leakage detected?
YES
>> GO TO 8.
NO
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following for leak. Refer to
• Hose
• Radiator
• Water pump
• Reservoir tank
>> Repair or replace.
8.
CHECK RESERVOIR TANK CAP
Check radiator cap. Refer to
CO-33, "RESERVOIR TANK CAP : Inspection"
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace radiator cap.
9.
CHECK THERMOSTAT
Check thermostat.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace thermostat.
10.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check engine coolant temperature sensor.
Is the inspection result normal?
OK
>> GO TO 11.
NG
>> Replace engine coolant temperature sensor.
11.
CHECK MAIN 13 CAUSES
If the cause cannot be isolated, check the following.
EC-1128
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
P1217 ENGINE OVER TEMPERATURE
*1: Turn the ignition switch ON.
*2: Engine running at 3,000 rpm for 10 minutes.
*3: Drive at 90 km/h (55 MPH) for 30 minutes and then let idle for 10 minutes.
*4: After 60 minutes of cool down time.
For more information, refer to
CO-26, "Troubleshooting Chart"
>> INSPECTION END
Engine
Step
Inspection item
Equipment
Standard
Reference page
OFF
1
• Blocked radiator
• Blocked condenser
• Blocked radiator grille
• Blocked bumper
• Visual
No blocking
—
2
• Coolant mixture
• Coolant tester
50 - 50% coolant mixture
3
• Coolant level
• Visual
Coolant up to MAX level in
reservoir tank and radiator
filler neck
4
• Reservoir tank cap
• Pressure tester
59 - 98 kPa
(0.6 - 1.0 bar, 0.6 - 1.0 kg/
cm
2
, 9 - 14 psi) (Limit)
CO-35, "Removal and In-
stallation"
ON*
2
5
• Coolant leaks
• Visual
No leaks
ON*
2
6
• Thermostat
• Touch the upper and
lower radiator hoses
Both hoses should be hot
CO-41, "Removal and In-
stallation"
ON*
1
7
• Cooling fan motor
• CONSULT-III
Operating
EC-920, "Component In-
spection (Cooling Fan
Motor)"
OFF
8
• Combustion gas leak
• Color checker chemical
tester 4 Gas analyzer
Negative
—
ON*
3
9
• Coolant temperature
gauge
• Visual
Gauge less than 3/4 when
driving
—
• Coolant overflow to res-
ervoir tank
• Visual
No overflow during driving
and idling
OFF*
4
10
• Coolant return from res-
ervoir tank to radiator
• Visual
Should be initial level in
reservoir tank
OFF
11
• Water control valve
• Remove and inspect
the valve
Within the specified value
CO-44, "Removal and In-
stallation"
OFF
12
• Cylinder head
• Straight gauge feeler
gauge
0.1 mm (0.004 in) Maxi-
mum distortion (warping)
EM-186, "Removal and
Installation"
13
• Cylinder block and pis-
tons
• Visual
No scuffing on cylinder
walls or piston
P1225 TP SENSOR
EC-1129
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1225 TP SENSOR
Description
INFOID:0000000001094230
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
DTC Logic
INFOID:0000000001094231
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1133, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001094232
1.
CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1.
Turn ignition switch OFF.
2.
Remove the intake air duct.
PBIB0145E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1225
Closed throttle position
learning performance
Closed throttle position learning value is exces-
sively low.
• Electric throttle control actuator
(TP sensor 1 and 2)
EC-1130
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
P1225 TP SENSOR
3.
Check if foreign matter is caught between the throttle valve (1)
and the housing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Remove the foreign matter and clean the electric throttle
control actuator inside.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
Go to
EC-1134, "Special Repair Requirement"
>> INSPECTION END
Special Repair Requirement
INFOID:0000000001094233
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-647, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-647, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
2.
Electric throttle control actuator
JMBIA0447ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст