Nissan Qashqai (2007-2010). Manual — part 1002
DOOR SWITCH
DLK-87
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace harness between BCM and door switch.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-87, "REAR LH : Component Inspection"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace malfunctioning door switch. Refer to
REAR LH : Component Inspection
INFOID:0000000001098051
1.
CHECK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door switch connector.
3.
Check door switch.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Replace malfunctioning door switch. Refer to
REAR RH
REAR RH : Description
INFOID:0000000001035857
Detects door open/close condition.
REAR RH : Component Function Check
INFOID:0000000001035858
1.
CHECK FUNCTION
With CONSULT-III
Check door switches “DOOR SW-RR” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Refer to
DLK-87, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000001098052
1.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check signal between BCM connector and ground with oscilloscope.
Terminal
Door switch condition
Continuity
Door switch
1
Ground part of door switch
Pressed
Exists
Released
Does not exist
Monitor item
Condition
DOOR SW-RR
OPEN
:ON
CLOSE
:OFF
DLK-88
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and door switch connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between BCM and door switch.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-88, "REAR RH : Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace malfunctioning door switch. Refer to
REAR RH : Component Inspection
INFOID:0000000001098053
1.
CHECK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door switch connector.
3.
Check door switch.
Is the inspection result normal?
YES
>> Door switch is OK.
NO
>> Replace malfunctioning door switch. Refer to
Terminals
Door condition
Voltage (V)
(Approx.)
(+)
(–)
BCM
connector
Terminal
M65
29
Ground
OPEN
0
CLOSE
JPMIA0011GB
BCM connector
Terminal
Door switch
connector
Terminal
Continuity
M65
29
B53
1
Exists
BCM connector
Terminal
Ground
Continuity
M65
29
Does not exist
Terminal
Door switch condition
Continuity
Door switch
1
Ground part of door switch
Pressed
Exists
Released
Does not exist
DOOR SWITCH
DLK-89
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
BACK DOOR : Description
INFOID:0000000000939119
Detects back door open condition.
BACK DOOR : Component Function Check
INFOID:0000000000939120
1.
CHECK FUNCTION
With CONSULT-III
Check “BACK DOOR SW” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES
>> Back door lock assembly (door switch) is OK.
NO
>> Refer to
DLK-89, "BACK DOOR : Diagnosis Procedure"
BACK DOOR : Diagnosis Procedure
INFOID:0000000000939121
1.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH) CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and back door lock assembly (door switch) connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness between BCM and trunk room lamp switch.
3.
CHECK BACK DOOR LOCK ASSEMBLY GROUND CIRCUIT
Check continuity between back door lock assembly connector and ground.
Monitor item
Condition
BACK DOOR SW
OPEN
: ON
CLOSE
: OFF
Terminals
Back door
condition
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M65
28
Ground
OPEN
0
CLOSE
Battery voltage
BCM connector
Terminal
Back door lock assembly
(door switch) connector
Terminal
Continuity
M65
28
D152
4
Exists
BCM connector
Terminal
Ground
Continuity
M65
28
Does not exist
DLK-90
< COMPONENT DIAGNOSIS >
[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace back door lock assembly ground circuit.
4.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace BCM. Refer to
5.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH)
Check back door lock assembly (door switch).
Refer to
DLK-90, "BACK DOOR : Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace back door lock assembly (door switch). Refer to
DLK-268, "DOOR LOCK : Exploded
DLK-268, "DOOR LOCK : Removal and Installation"
.
BACK DOOR : Component Inspection
INFOID:0000000000939122
1.
CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH)
1.
Turn ignition switch OFF.
2.
Disconnect back door lock assembly (door switch) connector.
3.
Check back door lock assembly (door switch).
Is the inspection result normal?
YES
>> Back door lock assembly (door switch) is OK.
NO
>> Replace back door lock assembly (door switch). Refer to
DLK-268, "DOOR LOCK : Exploded
DLK-268, "DOOR LOCK : Removal and Installation"
.
Back door lock assembly
(door switch) connector
Terminal
Ground
Continuity
D152
3
Exists
Terminals
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M65
28
Ground
Battery voltage
Terminal
Trunk condition
Continuity
Back door lock assembly (door switch)
4
3
OPEN
Exists
CLOSE
Does not exist
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст