Nissan Qashqai (2007-2010). Manual — part 521
CONTROL LINKAGE
TM-19
< ON-VEHICLE REPAIR >
[5MT: RS5F92R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL LINKAGE
Exploded View
INFOID:0000000001070440
Removal and Installation
INFOID:0000000001070441
REMOVAL
1.
Remove the air cleaner case and air duct (inlet). Refer to
EM-27, "Removal and Installation"
2.
Remove the battery. Refer to
PG-118, "Removal and Installation"
.
1.
Bracket
2.
Shift cable
3.
Control shaft assembly
4.
Cable mounting bracket
5.
Tapping bolt
6.
Select cable
7.
Grommet
8.
Control device assembly
9.
Control lever
10. Control lever knob
Refer to
for the symbols in the figure.
JPDIC0057GB
TM-20
< ON-VEHICLE REPAIR >
[5MT: RS5F92R]
CONTROL LINKAGE
3.
Disconnect the connectors (A) and then remove the bracket (1).
4.
While pressing the lock of the select cable in the direction of the
arrow shown in the figure, remove the select cable from the con-
trol shaft assembly.
5.
While pressing the lock of the shift cable in the direction of the
arrow shown in the figure, remove the shift cable from the con-
trol shaft assembly.
6.
While pulling the lock of the select cable in the direction of the
arrow shown in the figure, remove the select cable from the
cable mounting bracket.
7.
While pulling the lock of the shift cable in the direction of the
arrow shown in the figure, remove the shift cable from the cable
mounting bracket.
8.
Remove the control lever knob.
9.
Remove console finisher assembly and the center console
assembly. Refer to
IP-18, "Removal and Installation"
.
10. Shift the control lever to the neutral position.
11. While pressing the lock of the select cable in the direction of the
arrow shown in the figure, remove the select cable from the con-
trol device assembly.
12. While pressing the lock of the shift cable in the direction of the
arrow shown in the figure, remove the shift cable from the con-
trol device assembly.
13. While pulling the lock of the select cable in the direction of the
arrow shown in the figure, remove the select cable from the con-
trol device assembly.
14. While pulling the lock of the shift cable in the direction of the
arrow shown in the figure, remove the shift cable from the con-
trol device assembly.
15. Remove the control device assembly.
16. Remove the heat plate.
17. Remove the bracket.
JPDIA0240ZZ
JPDIC0066ZZ
JPDIC0067ZZ
JPDIC0066ZZ
JPDIC0067ZZ
CONTROL LINKAGE
TM-21
< ON-VEHICLE REPAIR >
[5MT: RS5F92R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
18. Remove the grommet and then remove the shift cable and select cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Shift the control lever to the neutral position.
• Securely assemble each cable and the lever of the control shaft assembly.
• Securely assemble each cable and the cable mounting bracket.
• Securely assemble each cable and the control device assembly.
• Make sure that the claws of grommet are in contact with the floor.
• Be careful about the installation direction and push the control lever knob into the control lever.
CAUTION:
Never reuse control lever knob.
• Tapping work for tapping bolt is not applied to new clutch housing. Do not perform tapping by other than
screwing tapping bolt because tapping is formed by screwing tapping bolt into clutch housing.
CAUTION:
Never reuse tapping bolt.
Inspection
INFOID:0000000001070442
After installing, confirm the following items:
• When the control lever is shifted to 1st-2nd side and 5th-Reverse side, confirm the control lever returns to
neutral position smoothly.
• When the control lever is shifted to each position, make sure there is no binding or disconnection in each
boot.
TM-22
< ON-VEHICLE REPAIR >
[5MT: RS5F92R]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000001070443
Removal and Installation
INFOID:0000000001070444
REMOVAL
Refer to the figure for removal procedure.
CAUTION:
When removing air breather hose, be sure to hold breather pipe securely.
INSTALLATION
Refer to the figure for installation procedure.
• When installing air breather hose on breather pipe, aim paint mark face toward the vehicle front.
• When installing air breather hose on breather pipe, push it until it hits transaxle case.
• When installing air breather hose to air cleaner case, make sure that clip are fully inserted.
CAUTION:
Make sure air breather hose is not collapsed or blocked due to folding or bending when installed.
1.
Air breather hose
2.
Transaxle assembly
3.
Breather pipe
4.
Air cleaner case
: Vehicle front
JPDIC0050ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст