Nissan Qashqai (2007-2010). Manual — part 978
![](/vehicle/qul/ene/roryboritele/omemaroswa.png)
SE-26
< ON-VEHICLE REPAIR >
FRONT SEAT
• Remove the TORX bolt (T25) (A).
• Pull the rear side of the seat cushion outer finisher frontward,
and then slide it forward to remove the pawls.Remove the seat
cushion outer finisher.
2.
Remove the seat cushion inner finisher.
• Remove the TORX bolt (T25) (A).
• Pull the rear side of the seat cushion inner finisher frontward,
and then slide it upward to remove the pawls.Remove the seat
cushion inner finisher.
3.
Remove the seatback assembly.
• Disconnect the seat cushion heater harness connect, and remove the harness clamp.
• Pull out the side air bag harness and seat heater harness from seat cushion trim.
• Remove the TORX bolt (T50) (A).
4.
Remove the seatback trim and seatback pad.
• Remove the lumbar support knob.
• Remove the seatback retainer (1) on the back side of the seat-
back.
: Pawl
JMJIA0352ZZ
: Pawl
JMJIA0353ZZ
JMJIA0354ZZ
JMJIA0356ZZ
![](/vehicle/qul/ene/roryboritele/pitetin.png)
FRONT SEAT
SE-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the mounting nut (A), and then remove side air bag
rod (1).
• Remove the seatback trim and seatback pad from the seatback frame.
• Remove the hog lings to separate the seatback trim and seatback pad.
5.
Remove the air bag module. Refer to
SR-12, "Removal and Installation"
6.
Remove the lumbar support unit.(Lumbar support model only.)
• Remove the TORX bolts (T20), and then remove lumbar support knob.
• Remove the spring, and then remove lumbar support unit.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the pad side wire.
SEAT CUSHION
Disassembly
1.
Remove the seat cushion outer finisher.
• Pull out the lifter lever knob while holding and raising the
pawls.
PIIB4084J
JMJIA0355ZZ
: Pawl
JMJIA0350ZZ
![](/vehicle/qul/ene/roryboritele/cei.png)
SE-28
< ON-VEHICLE REPAIR >
FRONT SEAT
• Pull out the reclining lever knob while holding and raising the
pawls.
• Remove the TORX bolt (T25) (A).
• Pull the rear side of the seat cushion outer finisher frontward,
and then slide it forward to remove the pawls.Remove the seat
cushion outer finisher.
2.
Remove the seat cushion inner finisher.
• Remove the TORX bolt (T25) (A).
• Pull the rear side of the seat cushion inner finisher frontward,
and then slide it upward to remove the pawls.Remove the seat
cushion inner finisher.
3.
Remove the seatback assembly.
• Disconnect the seat cushion heater harness connect, and remove the harness clamp.
• Pull out the side air bag harness and seat heater harness from seat cushion trim.
• Remove the TORX bolt (T50) (A).
4.
Remove the seat belt buckle. Refer to
SB-8, "SEAT BELT BUCKLE : Removal and Installation"
.
5.
Remove the seat cushion trim and seat cushion pad.
• Remove the seat cushion retainer.
• Remove the seat cushion heater harness, and occupant detection unit harness connector.
• Remove the hog rings, and separate the seat cushion trim and seat cushion pad, seat cushion heater
unit and occupant detection unit.
: Pawl
JMJIA0351ZZ
: Pawl
JMJIA0352ZZ
: Pawl
JMJIA0353ZZ
JMJIA0354ZZ
![](/vehicle/qul/ene/roryboritele/chelyo.png)
FRONT SEAT
SE-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
6.
Remove the seat slide assembly.
Remove the mounting nuts (A), and them remove seat slide
assembly.
7.
Remove the front slide cover.
8.
Remove the rear slide cover.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the pad side wire.
JMJIA0357ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст