Nissan Qashqai (2007-2010). Manual — part 1802
LAN
EPS BRANCH LINE CIRCUIT
LAN-1233
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 84)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
EPS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001058543
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the EPS control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of EPS control unit.
2.
Check the resistance between the EPS control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the EPS control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the EPS control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the EPS control unit. Refer to
YES (Past error)>>Error was detected in the EPS control unit branch line.
NO
>> Repair the power supply and the ground circuit.
EPS control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M37
8
6
Approx. 54 – 66
LAN-1234
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 84)]
I-KEY BRANCH LINE CIRCUIT
I-KEY BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001058544
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the Intelligent Key unit for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of Intelligent Key unit.
2.
Check the resistance between the Intelligent Key unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the Intelligent Key unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the Intelligent Key unit. Refer to
KEY UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES (Present error)>>Replace the Intelligent Key unit. Refer to
SEC-11, "Component Parts Location"
YES (Past error)>>Error was detected in the Intelligent Key unit branch line.
NO
>> Repair the power supply and the ground circuit.
Intelligent Key unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M40
2
3
Approx. 54 – 66
LAN
IPDM-E BRANCH LINE CIRCUIT
LAN-1235
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 84)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
IPDM-E BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001058546
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
IPDM E/R connector
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of IPDM E/R.
2.
Check the resistance between the IPDM E/R harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the IPDM E/R branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the IPDM E/R. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the IPDM E/R. Refer to
.
YES (Past error)>>Error was detected in the IPDM E/R branch line.
NO
>> Repair the power supply and the ground circuit.
IPDM E/R harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E12
28
29
Approx. 108 – 132
LAN-1236
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 84)]
CAN COMMUNICATION CIRCUIT
CAN COMMUNICATION CIRCUIT
Diagnosis Procedure
INFOID:0000000001058547
INSPECTION PROCEDURE
1.
CONNECTOR INSPECTION
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect all the unit connectors on CAN communication system.
4.
Check terminals and connectors for damage, bend and loose connection.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (SHORT CIRCUIT)
Check the continuity between the data link connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the harness and repair the root cause.
3.
CHECK HARNESS CONTINUITY (SHORT CIRCUIT)
Check the continuity between the data link connector and the ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Check the harness and repair the root cause.
4.
CHECK ECM AND IPDM E/R TERMINATION CIRCUIT
1.
Remove the ECM and the IPDM E/R.
2.
Check the resistance between the ECM terminals.
-
HR engine/MR engine models
-
K9K engine models
3.
Check the resistance between the IPDM E/R terminals.
Data link connector
Continuity
Connector No.
Terminal No.
M4
6
14
Not existed
Data link connector
Ground
Continuity
Connector No.
Terminal No.
M4
6
Not existed
14
Not existed
ECM
Resistance (
Ω
)
Terminal No.
84
83
Approx. 108 – 132
ECM
Resistance (
Ω
)
Terminal No.
100
99
Approx. 108 – 132
LKIA0037E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст