Nissan Qashqai (2007-2010). Manual — part 1210
![](/vehicle/qul/ene/roryboritele/urn.png)
SEC-40
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2195 ANTI-SCANNING
B2195 ANTI-SCANNING
Description
INFOID:0000000000944547
When the ID of the remote control engine starter installed cannot be registered, anti-scanning operates and it
may be possible that the engine can not start. In the case, obtain the customer approval to remove the remote
control engine starter.
DTC Logic
INFOID:0000000000944548
DTC DETECTION LOGIC
NOTE:
• If DTC B2195 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2195 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000000944549
1.
REMOVAL OF REMOTE CONTROL ENGINE STARTER
Remove remote control engine starter with the customer approval.
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
1.
Turn ignition switch ON.
2.
Perform “Self diagnostic result” with CONSULT-III.
3.
Erase DTC.
4.
Start the engine.
Does the engine start?
YES
>> INSPECTION END
NO
>>
BCM is malfunctioning.
• Replace BCM
• Perform initialization
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2195
ANTI-SCANNING
The ID of the remote control engine starter installed
cannot be registered.
Remote control engine starter
![](/vehicle/qul/ene/roryboritele/kins.png)
B2196 DONGLE NG
SEC-41
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2196 DONGLE NG
Description
INFOID:0000000001034035
BCM performs the ID verification with the slave control units (ECM, ABS actuator, EPS column assy, IPDM E/
R, combination meter).
If either slave control unit is replaced by used part, perform initialization with CONSULT-III. But if the control
unit is replaced by new part, the system does not need initialization.
DTC Logic
INFOID:0000000001034036
DTC DETECTION LOGIC
NOTE:
• If DTC B2196 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2196 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self Diagnostic Result” with CONSULT-III.
Is the DTC detected?
YES
>> Refer to
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001034037
1.
PERFORM INITIALIZATION
1.
Perform initialization with CONSULT-III. Re-register all mechanical keys. Refer to “CONSULT-III Opera-
tion Manual NATS”.
2.
Start the engine.
Dose the engine start?
YES
>> INSPECTION END
NO
>> Perform “Self Diagnosis Result” for each control unit.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2196
DONGLE NG
The ID verification results between BCM
and each slave control unit are NG.
• ECM
• ABS actuator assy
• EPS column assy
• Combination meter
• IPDM E/R
![](/vehicle/qul/ene/roryboritele/wntouben.png)
SEC-42
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2552 INTELLIGENT KEY
B2552 INTELLIGENT KEY
Description
INFOID:0000000001098017
Intelligent key unit performs engine start operation and steering lock control by crosschecking ID with the Intel-
ligent key.
DTC Logic
INFOID:0000000001098018
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
.
NO
>> INSPECTION END.
Diagnosis Procedure
INFOID:0000000001098019
1.
REPLACE INTELLIGENT KEY UNIT
1.
Replace Intelligent Key unit.
2.
Perform initialization with CONSULT-III. Re-register all mechanical keys. Refer to “CONSULT-III Opera-
tion Manual NATS”.
3.
Start the engine.
Does the engine start?
YES
>> INSPECTION END
NO
>> Perform “DTC confirmation procedure”. Refer to
.
Special Repair Requirement
INFOID:0000000001115369
1.
REQUIRED WORK WHEN REPLACING INTELLIGENT KEY UNIT
Initialize control unit. Refer to CONSULT-III operation manual NATS-IVIS/NVIS.
>> Work end.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2552
INTELLIGENT KEY
UNIT
Malfunction is detected inside Intelligent
key unit.
• Intelligent Key unit
![](/vehicle/qul/ene/roryboritele/xxpr.png)
B2590 ID DISCORD BCM-I-KEY
SEC-43
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2590 ID DISCORD BCM-I-KEY
Description
INFOID:0000000001109118
Intelligent Key unit performs the ID verification with BCM that allows the engine to start. BCM starts the engine
if the ID is OK and prevents the engine from starting if the ID is not registered.
DTC Logic
INFOID:0000000001109119
DTC DETECTION LOGIC
NOTE:
• If DTC B2590 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2590 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001109120
1.
PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all mechanical keys.
For initialization and registration of mechanical key. Refer to “CONSULT-III Operation Manual NATS”.
Can the system be initialized and can the engine be started with re-registered mechanical key?
YES
>> ID was unregistered.
NO
>>
BCM is malfunctioning.
• Replace BCM
• Perform initialization again
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2590
ID DISCORD BCM-I-
KEY
The ID verification results between BCM and Intel-
ligent Key unit are NG. The registration is neces-
sary.
• BCM
• Intelligent Key unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст