Subaru Baja (2006 year). Instruction — part 27
11-67
Maintenance and service
– CONTINUED –
T BAJA-Sport
1) Electrical connector
2) Push
1. Disconnect the electrical connector while pressing
the lock release tab.
2. Remove the bulb holder from the headlight assem-
bly by turning it counterclockwise.
3. Remove the bulb from the headlight assembly.
4. Install the new bulb.
5. Install the bulb holder in the headlight assembly by
turning it clockwise until it locks.
6. Remove the electrical connector.
1
2
UBB045BB
UBB046BA
11-68
Maintenance and service
T BAJA-Turbo
1) Low beam light bulb
2) High beam light bulb
Remove the headlight bulb cover, by turning it coun-
terclockwise.
UBB039BA
1
2
UBB040BB
11-69
Maintenance and service
– CONTINUED –
T Low beam light bulbs
0
1) Electrical connector
2) Red cable
3) Black cable
1. Disconnect the electrical connector for the black
cable.
2. Remove the retainer spring.
3. Replace the bulb, then set the retainer spring se-
curely.
4. Reconnect the electrical connector for black cable.
5. Install the headlight bulb cover.
1
2
3
UBB041BB
UBB042BA
11-70
Maintenance and service
T High beam light bulbs
0
1) Push
1. Disconnect the electrical connector from the bulb.
2. Remove the bulb from the headlight assembly by
turning it counterclockwise.
3. Replace the bulb with new one.
4. Reconnect the electrical connector. At this time,
use care not to touch the bulb surface.
5. To install the bulb to the headlight assembly, turn it
clockwise until it clicks.
6. Install the headlight bulb cover.
Front fog light
Replacing bulbs
Front fog light
Front
Fog light
It may be difficult to replace the bulbs. Have your
UBB043BA
1
UBB044BB
11-71
Maintenance and service
– CONTINUED –
SUBARU dealer replace the bulbs if necessary.
Front turn signal light, parking light
and side marker light
Replacing bulbs
Front turn signal light
Replacing bulbs
Parking light
Front
Turn signal light, parking light and side marker light
The headlight assembly must be removed before the
front turn signal light and parking light bulbs can be re-
placed. When the headlight assembly has been re-
moved and then reinstalled, it may become necessary
to make a headlight aiming adjustment. After a bulb
has been replaced, it is recommended that the head-
light aiming adjustment be made at a SUBARU dealer.
1. Remove the headlight assembly mounting screws
located at the top of and the front of the headlight as-
sembly using a Phillips screwdriver or an open-end
wrench.
2. Move the headlight assembly forward.
1) Front turn signal light bulb
2) Front turn signal light bulb/parking and front side
marker light bulb
3. Remove the bulb socket from the headlight assem-
bly by turning it counterclockwise.
UBB016BA
1
2
UBB039CB
11-72
Maintenance and service
4. Remove the bulb from the socket by pushing it and
turning counterclockwise. Install a new bulb in the
socket.
5. Set the bulb socket into the headlight assembly and
turn it clockwise until it locks.
6. Set the headlight assembly into the vehicle body.
Tighten the mounting screws.
Rear combination lights
Replacing bulbs
Rear combination lights
Rear
Combination lights
Rear combination lights are composed of the rear turn
signal/brake/tail light and backup lights.
T Rear turn signal/Brake/Tail and Backup lights
The rear turn signal/brake/tail light is one bulb with two
filament types.
If any one of them malfunctions, replace the bulb with
a new one.
1. Open the tailgate.
2. Pry the cover from the side of the rear combination
light.
UBB020BA
UBB083BA
11-73
Maintenance and service
– CONTINUED –
3. Remove the rear combination light mounting bolts.
Then, slide the rear combination light assembly to the
rear and remove it from the vehicle.
1) Backup light bulb
2) Brake/turn/tail/light bulb
4. Remove the bulb socket from the rear combination
light assembly by turning it counterclockwise.
5. Remove the bulb from the socket by pulling it.
6. Install a new bulb into the socket by pushing it.
7. Set the bulb socket into the rear combination light
assembly and turn it clockwise until it stops.
8. Mount the rear combination light assembly into the
vehicle body with two mounting bolts.
9. Install the cover by inserting the knobs into the
places.
UBB084BA
2
1
UBB085BB
11-74
Maintenance and service
Tail light (on the tailgate)
Replacing bulbs
Tail light
Tail light
1. Open the tailgate.
2. Remove the tailgate trim by loosening the installa-
tion screws.
3. Remove the tail light cover by loosening the instal-
lation screws.
UBB086BA
UBB087BA
11-75
Maintenance and service
– CONTINUED –
4. Remove the bulb socket from the tail light by turn-
ing it counterclockwise.
5. Remove the bulb from the socket by pulling it.
6. Install a new bulb into the socket by pushing it.
7. Install the bulb socket into the tail light by turning it
clockwise until it stops.
8. Install the tail light cover and the tailgate trim.
UBB088BA
UBB048BA
11-76
Maintenance and service
License plate light
License plate light
Replacing bulbs
License plate light
0
1. Push two release buttons and pull the license plate
bracket up until it clicks.
2. Remove the two cover installation screws.
3. Push the license plate bracket back to the original
position.
UBB096BA
UBB097BA
11-77
Maintenance and service
– CONTINUED –
4. Remove the screw from the side of the cover.
5. Remove the cover.
6. Remove the bulb socket from the license plate
bracket by turning it counterclockwise.
7. Pull the bulb out of the socket.
8. Install a new bulb in the socket by pushing it.
9. Install the bulb socket into the license plate bracket.
10.Install the covers by reversing procedures for re-
moval.
UBB092BA
UBB093BA
11-78
Maintenance and service
Map light, dome light and door step
light
Replacing bulbs
Dome light
Dome light
Replacing bulbs
Map light
Map light
Dome light
UBB068BA
HSB088BA
11-79
Maintenance and service
– CONTINUED –
Door step light
1. Remove the lens by prying the edge of the lens with
a flat-head screwdriver.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the lens.
High mount stop and cargo light as-
sembly
Replacing bulbs
High mount stop light assembly
Replacing bulbs
Cargo light assembly
High mount stop and cargo light assembly
1. Remove the high mount stop light mounting
screws.
UBS037AA
UBB089BA
11-80
Maintenance and service
1) Cargo lights
2) High mount stop lights
2. Remove the bulb socket from the light assembly by
turning it counterclockwise.
3. Remove the bulb from the socket by pulling it.
4. Install a new bulb in the socket by pushing it.
5. Set the socket into the light assembly and turn it
clockwise until it clicks.
6. Mount the light assembly with the mounting
screws.
1
2
UBB090BB
UBB048BA
11-81
Maintenance and service
– CONTINUED –
Sport activity lights (if equipped)
Sport activity lights
1. Remove front lamp screw and remove the lens and
reflector.
2. Disconnect the two wires from the lamp electrical
connector.
3. Squeeze the bulb retainer spring to remove.
4. Replace the bulb, then reset the retainer spring se-
curely.
5. Reconnect the bulb wire to the electrical connector.
6. Install the lens and reflector in the housing and se-
cure with the screw.
NOTE
Other bulbs may be difficult to replace. Have your
SUBARU dealer replace these bulbs if necessary.
UBB081BA
UBB082BA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст