Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 428
6MT-49
Extension Case
MANUAL TRANSMISSION AND DIFFERENTIAL
2) Measure depth “Y” between the end of the ST
and the transfer drive gear.
ST 398643600
GAUGE
3) Using the following calculation, calculate the
transfer drive gear adjusting washer value “t”.
t = {Y – 15 mm (0.59 in)} – {Z – 15 mm (0.59 in)} –
0.75 — 0.95 mm (0.030 — 0.037 in)
4) Refer to the calculated value “t” to select the
closest adjusting washer from the following table.
Standard clearance between the adjusting
washer and transfer drive gear
0.75 — 0.95 mm (0.030 — 0.037 in)
NOTE:
Match to be within the standard clearance range.
5) Install the selected adjusting washer.
t
mm (in)
Transfer drive gear adjusting washer
thickness
Y
mm (in)
Depth between the end of the ST
and the transfer drive gear
Z
mm (in)
Height from the end of the transmis-
sion case to the end of the ST.
0.75 — 0.95 mm
(0.030 — 0.037 in)
Standard clearance between the
adjusting washer and transfer drive
gear
15 mm (0.591 in)
Thickness of ST
MT-01421
ST
ST
Y
Adjusting washer (36.3 × 52 × t)
Part No.
Thickness mm (in)
803036070
0.80 (0.0315)
803036071
0.95 (0.0374)
803036072
1.10 (0.0433)
803036073
1.25 (0.0492)
803036074
1.40 (0.0551)
803036075
0.65 (0.0256)
6MT-50
Reverse Check System
MANUAL TRANSMISSION AND DIFFERENTIAL
12.Reverse Check System
A: REMOVAL
1) Remove the manual transmission assembly
from the vehicle. <Ref. to 6MT-31, REMOVAL,
Manual Transmission Assembly.>
2) Prepare the transmission for overhaul. <Ref. to
6MT-37, Preparation for Overhaul.>
3) Remove the extension case. <Ref. to 6MT-43,
4) Remove the snap ring and washer from the re-
verse check shaft.
5) Remove the reverse check shaft and spring from
the extension case.
6) Remove the straight pin, and remove the re-
verse check lever and oil seal from the reverse
check shaft.
7) Remove the plug from the extension case, and
remove the gasket, spring and plunger.
8) Remove the reverse lock plunger.
(A) Snap ring
(B) Washer
MT-00494
(A)
(B)
MT-00495
(A) Straight pin
(B) Reverse check lever
(C) Oil seal
(A) Plug
(B) Gasket
(C) Spring
(D) Plunger
(A) Reverse lock plunger
MT-00496
(A)
(C)
(B)
MT-01818
(A)
(B)
(C)
(D)
MT-00498
(A)
6MT-51
Reverse Check System
MANUAL TRANSMISSION AND DIFFERENTIAL
B: INSTALLATION
1) Insert the reverse lock plunger.
2) Install the reverse check plug, spring, gasket,
and plug in order.
NOTE:
Use a new gasket.
Tightening torque:
41 N·m (4.2 kgf-m, 30.2 ft-lb)
3) Install the spring and reverse check shaft to the
extension case.
NOTE:
Confirm that the end of the spring matches the hole
of the reverse check shaft and the cut out of the ex-
tension case.
4) Install the washer and snap ring.
(A) Plug
(B) Gasket
(C) Spring
(D) Reverse check plug
MT-01818
(A)
(B)
(C)
(D)
(A) Reverse check shaft
(B) Spring
(C) Hole
(D) Cut out
(A) Snap ring
(B) Washer
(A)
(A)
(C)
(D)
(B)
(B)
MT-00499
MT-00494
(A)
(B)
6MT-52
Reverse Check System
MANUAL TRANSMISSION AND DIFFERENTIAL
5) Attach ST1 to the reverse check shaft. Install the
new oil seal, and push it in using ST2.
ST1 18671AA000
OIL SEAL GUIDE
ST2 18657AA010
INSTALLER
6) Insert the reverse check lever, and turn the re-
verse check shaft until the plunger is first pushed
in.
7) Match the hole of the reverse check lever and
the reverse check shaft, and attach the straight pin.
NOTE:
Use a new straight pin.
8) Check that the reverse check is operating cor-
rectly. <Ref. to 6MT-52, INSPECTION, Reverse
9) Install the extension case. <Ref. to 6MT-43, IN-
10) Install the manual transmission assembly to the
vehicle. <Ref. to 6MT-33, INSTALLATION, Manual
C: INSPECTION
1) Check that there is no damage on any parts.
2) Check that the reverse check lever is operating
smoothly.
3) Inspect that there is no oil leak at the oil seal sec-
tion of the reverse check shaft. If there is oil leak-
age, replace the oil seal.
4) Check the operation of the reverse check.
(1) When the reverse check lever is in the fol-
lowing position, the plunger is pressed, or the
gear can shift into reverse.
(2) When the reverse check lever is in the fol-
lowing position, the plunger is not pressed, or
the gear cannot shift into reverse.
5) If it is not as specified, reassemble the reverse
check system.
(A) Oil seal
(A) Plunger
(B) Reverse check shaft
(A) Reverse check shaft
(B) Reverse check lever
(C) Hole
MT-00500
(A)
ST2
ST1
MT-00501
(A)
(B)
MT-00502
(A)
(B)
(C)
MT-00503
MT-00504
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст