Subaru Legacy (2005 year). Service manual — part 143
EN(H4SO 2.0)(diag)-161
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AT:DTC P0605 INTERNAL CONTROL MODULE READ ONLY MEMORY (ROM)
ERROR
NOTE:
For the diagnostic procedure, refer to DTC P0607. <Ref. to EN(H4SO 2.0)(diag)-162, DTC P0607 CON-
TROL MODULE PERFORMANCE, Diagnostic Procedure with Diagnostic Trouble Code (DTC).>
Step
Check
Yes
No
1
CHECK ANY OTHER DTC ON DISPLAY.
Is any other DTC displayed?
Inspect the rele-
vant DTC using
“List of Diagnostic
Trouble Code
(DTC)”. <Ref. to
EN(H4SO
2.0)(diag)-64, List
of Diagnostic Trou-
ble Code (DTC).>
Temporary poor
contact occurs.
EN(H4SO 2.0)(diag)-162
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AU:DTC P0607 CONTROL MODULE PERFORMANCE
DTC DETECTING CONDITION:
Immediately at fault recognition
TROUBLE SYMPTOM:
• Erroneous idling
• Poor driving performance
CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4SO 2.0)(diag)-
38, OPERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H4SO 2.0)(diag)-32, PRO-
CEDURE, Inspection Mode.>.
WIRING DIAGRAM:
EN-03509
BATTERY
IGNITION
SWITCH
MAIN RELAY
SBF-6
MAIN SBF
SBF-7
B72
C4
C3
B14
B5
C6
B6
C1
C2
A7
C5
C7
B13
No.12
B47
2
1
4
6
5
3
E
E
3
6
D1
36
3
4
1
2
5
6
B47
No.13
A2
B137
5
6
7
8
2
1
9
4
3
10
22 23
11 12 13 14 15
24 25
26
16 17
18 19 20 21
27
28 29
30 31
B21
1 2 3 4
12 13 14 15
5 6 7 8
16 17 18 19
9 10 11
20 21 22
23 24 25 26 27 28 29 30 31 32 33
35
34
37
36
39
38
41
40
43
42
44
45
47
46
49
48
51
50
53
52
54
B72
1
3
4 5 6
2
B134
5
6
7
8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16 17
18 19 20 21
33 34
29
32
30 31
A:
B135
5
6
7
8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16 17 18 19
20 21
29 30 31
32 33
34 35
B:
D:
ECM
B134
B135
A:
D: B137
B:
B136
C:
B136
5
6
7 8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16
17 18 19 20 21
33 34
29
32
30
31
35
C:
52
37
34
35
E78
E1
B20
20
39
38
19
5
2
15
16
ELECTRONIC
THROTTLE CONTROL
E
1
1
B83
:LHD
B138 :RHD
*
*
2
2
B83
:LHD
B138 :RHD
*
*
4
*
6
*
3
*
5
*
D2
D3
D4
D5
C18
C30
C17
D24
D23
E2
B21
SBF-5
*
1
: TERMINAL No.
RANDOM
ARRANGEMENT
AMONG 3,4,7, AND 8
*
2
: TERMINAL No.
RANDOM
ARRANGEMENT
AMONG 1,2,5, AND 6
*
3
LHD : 4
RHD : 6
*
4
LHD : 6
RHD : 4
*
5
LHD : 3
RHD : 1
*
6
LHD : 1
RHD : 3
E78
1 2 3 4
5 6 7 8
B83
B138
B20
TO OXYGEN SENSOR
1 2 3 4
5 6 7 8
9 10 11 12
14
13
15 16
EN(H4SO 2.0)(diag)-163
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AV:DTC P0638 THROTTLE ACTUATOR CONTROL RANGE/PERFORMANCE
(BANK 1)
NOTE:
For the diagnostic procedure, refer to DTC P2101. <Ref. to EN(H4SO 2.0)(diag)-190, DTC P2101 THROT-
TLE ACTUATOR CONTROL MOTOR CIRCUIT RANGE/PERFORMANCE, Diagnostic Procedure with Di-
agnostic Trouble Code (DTC).>
Step
Check
Yes
No
1
CHECK INPUT VOLTAGE OF ECM.
1) Turn the ignition switch to ON.
2) Measure the voltage between ECM con-
nector and chassis ground.
Connector & terminal
(B136) No. 3 (+) — Chassis ground (
−
):
(B136) No. 4 (+) — Chassis ground (
−
):
Is the voltage 10 — 13 V?
Repair the open or
ground short cir-
cuit of power sup-
ply circuit.
2
CHECK INPUT VOLTAGE OF ECM.
1) Start the engine.
2) Measure the voltage between ECM con-
nector and chassis ground.
Connector & terminal
(B136) No. 3 (+) — Chassis ground (
−
):
(B136) No. 4 (+) — Chassis ground (
−
):
Is the voltage 13 — 15 V?
Repair the open or
ground short cir-
cuit of power sup-
ply circuit.
3
CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and
electronic throttle control.
3) Measure the resistance of harness
between ECM and electronic throttle control
connector.
Connector & terminal
LHD model
(B135) No. 4 — (E24) No. 17:
(E78) No. 1 — (B136) No. 18:
RHD model
(E78) No. 6 — (B136) No. 17:
(E78) No. 3 — (B136) No. 18:
Is the resistance less than 1
Ω?
Repair the open
circuit of harness
between ECM and
electronic throttle
control connector.
4
CHECK ECM GROUND HARNESS.
Measure the voltage between ECM connector
and chassis ground.
Connector & terminal
(B136) No. 2 (+) — Chassis ground (
−
):
(B136) No. 5 (+) — Chassis ground (
−
):
(B136) No. 6 (+) — Chassis ground (
−
):
Is the voltage less than 1 V?
Repair the poor
contact in ECM
connector.
Replace the ECM
if defective. <Ref.
to FU(H4SO 2.0)-
34, Engine Con-
trol Module
(ECM).>
Further tighten the
engine ground ter-
minal.
EN(H4SO 2.0)(diag)-164
ENGINE (DIAGNOSTICS)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AW:DTC P0691 FAN 1 CONTROL CIRCUIT LOW
DTC DETECTING CONDITION:
Detects when malfunction occurs in 2 continuous driving cycles.
TROUBLE SYMPTOM:
• Radiator fan does not operate properly.
• Overheating
CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4SO 2.0)(diag)-
38, OPERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H4SO 2.0)(diag)-32, PRO-
CEDURE, Inspection Mode.>.
AX:DTC P0692 FAN 1 CONTROL CIRCUIT HIGH
DTC DETECTING CONDITION:
Detects when malfunction occurs in 2 continuous driving cycles.
TROUBLE SYMPTOM:
• Radiator fan does not operate properly.
• Overheating
CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4SO 2.0)(diag)-
38, OPERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H4SO 2.0)(diag)-32, PRO-
CEDURE, Inspection Mode.>.
AY:DTC P0700 TRANSMISSION CONTROL SYSTEM (MIL REQUEST)
NOTE:
For the diagnostic procedure, refer to AT section. <Ref. to 4AT(diag)-2, Basic Diagnostic Procedure.>
Step
Check
Yes
No
1
CHECK ANY OTHER DTC ON DISPLAY.
Is DTC P0691 displayed on the
Subaru Select Monitor?
Check the radiator
fan system. <Ref.
to CO(H4SO 2.0)-
7, Radiator Fan
System.>
Temporary poor
contact occurs.
Step
Check
Yes
No
1
CHECK ANY OTHER DTC ON DISPLAY.
Is DTC P0692 displayed on the
Subaru Select Monitor?
Check the radiator
fan system. <Ref.
to CO(H4SO 2.0)-
7, Radiator Fan
System.>
Temporary poor
contact occurs.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст