Subaru Legacy (2005 year). Service manual — part 509
4AT-17
AUTOMATIC TRANSMISSION
General Description
11.ATF COOLER (WITH ATF WARMER FUNCTION)
(1)
ATF cooler outlet hose
(5)
Engine coolant inlet hose
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
ATF cooler inlet hose
(6)
Engine coolant outlet hose
T: 23 (2.3, 17)
(3)
Hose clamp
(7)
ATF cooler bracket
(4)
ATF cooler ASSY
(8)
Clip
AT-03198
(4)
(3)
(3)
(3)
(3)
(3)
(5)
(3)
(8)
(7)
(1)
(6)
T
(3)
(3)
(2)
4AT-18
AUTOMATIC TRANSMISSION
General Description
12.TRANSMISSION MOUNTING
(1)
Pitching stopper
(3)
Crossmember
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Rear cushion rubber
(4)
Stopper
T1: 35 (3.6, 26)
T2: 40 (4.1, 29.5)
T3: 50 (5.1, 36.9)
T4: 58 (5.9, 42.8)
T5: 70 (7.1, 51.6)
AT-00014
(2)
(3)
(4)
(1)
T4
T3
T5
T5
T2
T2
T1
4AT-19
AUTOMATIC TRANSMISSION
General Description
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Do not place the oil pan with its inner side facing
upward until it is installed so as to prevent foreign
matter intrusion into valve body.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• When disassembling the case and other light al-
loy parts, use a plastic hammer to open the case.
Do not pry it apart with a screwdriver or other tool.
• Be careful not to burn yourself, because each
part on the vehicle is hot after running.
• Use SUBARU genuine gear oil, grease etc. or
the equivalent. Do not mix gear oil, grease etc. with
that of another grade or from other manufacturers.
• Be sure to tighten bolts and nuts to the specified
torque.
• Place a lift, a shop jack or a rigid rack at the spec-
ified position.
• Before installation, apply gear oil or ATF onto
sliding or revolution surface according to purpose
of part.
• Replace deformed or otherwise damaged snap
rings with new ones.
• Before installing O-rings or oil seals, apply suffi-
cient amount of ATF to avoid damage and defor-
mation.
• Be careful not to incorrectly install or fail to install
O-rings, snap rings and other such parts.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or cloth between the part and the vise.
• Avoid damaging the mating surface of the case.
• Before applying liquid gasket, completely re-
move the old seal.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
498575400
OIL PRESSURE
GAUGE ASSY
Used for measuring oil pressure.
498897200
ADAPTER
Used for oil pump housing when measuring
reverse clutch pressure and line pressure.
ST-498575400
ST-498897200
4AT-20
AUTOMATIC TRANSMISSION
General Description
498897700
ADAPTER SET
Used for measuring transfer clutch pressure.
498545400
FILTER WRENCH
Used for removing and installing ATF filter.
498277200
STOPPER SET
Used for removing and installing automatic
transmission assembly to engine.
398527700
PULLER ASSY
• Used for removing extension case roller bear-
ing.
• Used for removing extension oil seal.
• Used for removing front differential side
retainer bearing outer race.
• Used for removing front differential side
retainer oil seal.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-498897700
ST-498545400
ST-498277200
ST-398527700
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст