Subaru Legacy (2005 year). Service manual — part 319
EN(H4DOTC)(diag)-45
ENGINE (DIAGNOSTICS)
Malfunction Indicator Light
E: MALFUNCTION INDICATOR LIGHT DOES NOT BLINK.
DIAGNOSIS:
• The malfunction indicator light circuit is open or shorted.
• Test mode connector circuit is open.
TROUBLE SYMPTOM:
Malfunction indicator light does not blink during inspection mode.
WIRING DIAGRAM:
EN-03517
SBF-6
MAIN SBF
No.5
B72
B38
B75
B76
B134
B137
ECM
i3
E
3
6
1
1
*
A17
D15
i10
A:
D:
B72
B75
B76
i10
B137
1
2
1
2
1
2
1
2
D:
COMBINATION
METER
IGNITION
SWITCH
: TERMINAL No. RANDOM ARRANGEMENT
BATTERY
B134
B38
A:
5
6
7
8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16 17
18 19 20 21
33 34
29
32
30 31
5
6
7
8
2
1
9
4
3
10
22 23
11 12 13 14 15
24 25
26
16 17
18 19 20 21
27
28 29
30 31
4
16
3
8
*
*
C19
B138
1
3
4 5 6
2
2
1
3 4
6 7 8 9 10
22
21
20
19
18
17
16
15
14
13
12
11
5
1 2 3 4
5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
1 2 3 4
5 6 7 8
B138
B136
C:
B136
5
6
7 8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16
17 18 19 20 21
33 34
29
32
30
31
35
C :
EN(H4DOTC)(diag)-46
ENGINE (DIAGNOSTICS)
Malfunction Indicator Light
Step
Check
Yes
No
1
CHECK STATUS OF MALFUNCTION INDI-
CATOR LIGHT.
1) Turn the ignition switch to OFF.
2) Disconnect the test mode connectors.
3) Turn the ignition switch to ON. (engine
OFF)
Does the malfunction indicator
light illuminate?
Repair the mal-
function indictor
light circuit. <Ref.
to
EN(H4DOTC)(diag
)-42, MALFUNC-
TION INDICATOR
LIGHT DOES NOT
COME ON, Mal-
function Indicator
Light.>
2
CHECK HARNESS BETWEEN COMBINA-
TION METER AND ECM CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Turn the ignition switch to ON.
Does the malfunction indicator
light illuminate?
Repair the ground
short circuit of har-
ness between
combination meter
and ECM connec-
tor.
3
CHECK HARNESS BETWEEN TEST MODE
CONNECTOR AND ECM.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance of harness
between test mode connector and ECM.
Connector & terminal
(B76) No. 1 — (B136) No. 19:
Is the resistance less than 1
Ω?
Repair the har-
ness and connec-
tor.
NOTE:
In this case, repair
the following:
• Open circuit of
harness between
test mode connec-
tor and ECM
• Poor contact in
joint connector
4
CHECK POOR CONTACT.
Check poor contact in ECM connector.
Is there poor contact in ECM
connector?
Repair the poor
contact in ECM
connector.
5
CHECK HARNESS BETWEEN ECM AND
TEST MODE CONNECTOR.
Measure the resistance of harness between
ECM and test mode connector.
Connector & terminal
(B137) No. 15 — (B75) No. 1:
Is the resistance less than 1
Ω?
Repair the open
circuit of harness
between ECM and
test mode connec-
tor.
6
CHECK POOR CONTACT.
Check poor contact in ECM connector.
Is there poor contact in ECM
connector?
Repair the poor
contact in ECM
connector.
Replace the ECM.
<Ref. to
FU(H4DOTC)-34,
Engine Control
Module (ECM).>
EN(H4DOTC)(diag)-47
ENGINE (DIAGNOSTICS)
Malfunction Indicator Light
F: MALFUNCTION INDICATOR LIGHT REMAINS BLINKING.
DIAGNOSIS:
Test mode connector circuit is shorted.
TROUBLE SYMPTOM:
Malfunction indicator light blinks when test mode connector is not connected.
WIRING DIAGRAM:
Step
Check
Yes
No
1
CHECK TEST MODE CONNECTOR.
1) Disconnect the test mode connectors.
2) Turn the ignition switch to ON.
Does the malfunction indicator
light blink?
System is in good
order.
NOTE:
Malfunction indica-
tor light blinks at a
cycle of 3 Hz when
test mode connec-
tor is connected.
EN-03517
SBF-6
MAIN SBF
No.5
B72
B38
B75
B76
B134
B137
ECM
i3
E
3
6
1
1
*
A17
D15
i10
A:
D:
B72
B75
B76
i10
B137
1
2
1
2
1
2
1
2
D:
COMBINATION
METER
IGNITION
SWITCH
: TERMINAL No. RANDOM ARRANGEMENT
BATTERY
B134
B38
A:
5
6
7
8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16 17
18 19 20 21
33 34
29
32
30 31
5
6
7
8
2
1
9
4
3
10
22 23
11 12 13 14 15
24 25
26
16 17
18 19 20 21
27
28 29
30 31
4
16
3
8
*
*
C19
B138
1
3
4 5 6
2
2
1
3 4
6 7 8 9 10
22
21
20
19
18
17
16
15
14
13
12
11
5
1 2 3 4
5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
1 2 3 4
5 6 7 8
B138
B136
C:
B136
5
6
7 8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16
17 18 19 20 21
33 34
29
32
30
31
35
C :
EN(H4DOTC)(diag)-48
ENGINE (DIAGNOSTICS)
Malfunction Indicator Light
2
CHECK HARNESS BETWEEN ECM CON-
NECTOR AND CHASSIS GROUND TERMI-
NAL.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Measure the resistance of harness
between ECM connector and chassis ground.
Connector & terminal
(B137) No. 15 — Chassis ground:
Is the resistance less than 5
Ω?
Repair the short
circuit of harness
between ECM and
test mode connec-
tor.
Replace the ECM.
<Ref. to
FU(H4DOTC)-34,
Engine Control
Module (ECM).>
Step
Check
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст