Subaru Legacy (2005 year). Service manual — part 491
CS-5
CONTROL SYSTEMS
General Description
3. 6MT GEAR SHIFT LEVER
T4
T5
T3
(7)
(6)
(8)
(25)
(26)
(27)
(21)
(22)
(23)
(24)
(20)
(19)
(18)
T1
(15)
(17)
(16)
(14)
(13)
(12)
(30)
(31)
(12)
(11)
(10)
(9)
(29)
(28)
(13)
(13)
(33)
(12)
(12)
(12)
(12)
T3
T3
(34)
(36)
(37)
(36)
(35)
CS-00561
T4
(5)
(3)
(3)
(4)
(2)
(1)
(32)
CS-6
CONTROL SYSTEMS
General Description
4. DRIVE SELECT LEVER
(1)
Gear shift knob
(16)
Bushing
(31)
Reverse check lever
(2)
Front cover ASSY
(17)
Spring pin
(32)
Band clip
(3)
Clamp
(18)
Bushing
(33)
Boss
(4)
Boot and insulator ASSY
(19)
Boot
(34)
O-ring
(5)
Plate ASSY
(20)
Stay
(35)
O-ring
(6)
Slider
(21)
Cushion rubber
(36)
Screw
(7)
Spring pin
(22)
Bushing
(37)
Spring seat
(8)
Spring
(23)
Reverse check cable
(9)
Holder
(24)
Washer
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(10)
Seat cushion
(25)
Snap pin
T1: 1.3 (0.13, 0.96)
(11)
Lever
(26)
Bracket
T2: 7.5 (0.76, 5.5)
(12)
Bushing
(27)
Cable plate
T3: 12 (1.2, 8.9)
(13)
Spacer
(28)
Joint
T4: 18 (1.8, 13.3)
(14)
Lock wire
(29)
Spring pin
T5: 32 (3.3, 23.6)
(15)
Snap ring
(30)
Rod
(1)
Cover
(7)
Plate ASSY
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Knob
(8)
Bushing
T1: 4.5 (0.46, 3.3)
(3)
Lever ASSY
(9)
Clevis pin
T2: 12 (1.2, 8.9)
(4)
Bushing
(10)
Snap pin
T3: 27.5 (2.80, 20.3)
(5)
Spacer
(11)
Cable
(6)
Spring
(12)
Clip
CS-00371
(10)
(11)
(12)
(4)
(4)
(3)
(7)
T2
T2
T2
T1
T1
T3
(8)
(9)
(5)
(1)
(2)
(6)
CS-7
CONTROL SYSTEMS
General Description
C: PREPARATION TOOL
1. SPECIAL TOOL
D: CAUTION
• Wear work clothing, including a cap, protective
goggles, and protective shoes during operation.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• Use SUBARU genuine fluid, grease etc. or
equivalent. Do not mix fluid, grease, etc. with that of
another grade or from other manufacturers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Apply grease onto sliding or revolution surfaces
before installation.
• Before installing O-rings or snap rings, apply suf-
ficient amount of fluid to avoid damage and defor-
mation.
• Before securing a part in a vice, place cushioning
material such as wood blocks, aluminum plate, or
cloth between the part and vice.
• Before disconnecting electrical connectors, be
sure to disconnect the ground cable from battery.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
18482AA000
(Newly adopted tool)
CARTRIDGE
Troubleshooting for electrical system.
22771AA030
SUBARU SELECT
MONITOR KIT
Troubleshooting for electrical system.
• English: 22771AA030 (Without printer)
• German: 22771AA070 (Without printer)
• French: 22771AA080 (Without printer)
• Spanish: 22771AA090 (Without printer)
ST18482AA000
ST22771AA030
CS-8
CONTROL SYSTEMS
AT Shift Lock Control System
2. AT Shift Lock Control System
A: LOCATION
(1)
TCM (“P” range)
(4)
Key cylinder (with built-in key
warning switch)
(6)
“P” range switch
(2)
Body integrated module
(7)
Key lock solenoid
(3)
Stop light switch
(5)
Shift lock solenoid unit
CS-00513
(1)
(3)
(2)
(5)
(6)
(7)
(4)
CS-00514
(1)
CS-00515
(2)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст