Subaru Legacy (2005 year). Service manual — part 579
5AT-15
AUTOMATIC TRANSMISSION
General Description
10.TRANSMISSION CONTROL DEVICE & PARKING SUPPORT
(1)
Bracket
(7)
Manual plate
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Floating bracket
(8)
Parking rod
T1: 6 (0.6, 4.4)
(3)
AT main case
(9)
Parking support actuator
T2: 25 (2.5, 18.4)
(4)
Range select lever
(10)
Parking pawl shaft
T3: <Ref. to 5AT-80, Parking Pawl.>
(5)
Straight pin
(11)
Return spring
(6)
Detent spring
(12)
Parking pawl
AT-03022
T2
T2
T3
T1
T1
(1)
(2)
(3)
(10)
(11)
(8)
(7)
(5)
(4)
(6)
(12)
(9)
5AT-16
AUTOMATIC TRANSMISSION
General Description
11.TRANSMISSION CONTROL MODULE
(1)
Transmission control module
(TCM) (RHD model)
(3)
Lateral G sensor
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(4)
Transmission control module
(TCM) (LHD model)
T1: 7.5 (0.76, 5.5)
(2)
Relay
T2: 24.5 (2.5, 18.1)
AT-02036
T2
T1
T1
(3)
(2)
(1)
(2)
(4)
T1
5AT-17
AUTOMATIC TRANSMISSION
General Description
12.TRANSMISSION MOUNTING
(1)
Pitching stopper
(3)
Crossmember
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Rear cushion rubber
(4)
Stopper
T1: 35 (3.6, 26)
T2: 40 (4.1, 29.5)
T3: 50 (5.1, 36.9)
T4: 58 (5.9, 42.8)
T5: 70 (7.1, 51.6)
AT-01738
(2)
(3)
(4)
(1)
T4
T5
T5
T2
T2
T1
T3
S552.fm 17 ページ 2007年12月3日 月曜日 午後1時42分
5AT-18
AUTOMATIC TRANSMISSION
General Description
C: CAUTION
• Wear work clothing, including a cap, protective
goggles and protective shoes during operation.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Until the oil pan is removed, do not place with the
oil pan side facing up to prevent foreign matter from
entering the valve body.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, disassembly and replacement.
• When disassembling the case and other light al-
loy parts, disassemble them by slightly tapping with
a plastic hammer. Do not pry it apart with a screw-
driver or other tool.
• Be careful not to burn yourself, because each
part on the vehicle is hot after running.
• Use SUBARU genuine gear oil, grease etc. or
the equivalent. Do not mix them with that of another
grade or from other manufacturers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Apply gear oil onto sliding or revolution surfaces
before installation.
• Replace deformed or otherwise damaged snap
rings with new ones.
• Before installing O-rings or oil seals, apply suffi-
cient amount of ATF fluid to avoid damage and de-
formation.
• Be careful not to incorrectly install or fail to install
O-rings, snap rings and other such parts.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or cloth between the part and the vise.
• Avoid damaging the mating surface of the case.
• Before applying liquid gasket, completely re-
move the old seal.
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
498575400
OIL PRESSURE
GAUGE ASSY
Used for measuring oil pressure.
498897200
ADAPTER
• Used with oil pump cover installed on when
measuring line pressure.
• Used with extension case installed on when
measuring transfer clutch pressure.
ST-498575400
ST-498897200
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст