Subaru Legacy (2005 year). Service manual — part 63
ME(H4SO 2.0)-35
MECHANICAL
Engine Mounting
10.Engine Mounting
A: REMOVAL
1) Remove the engine assembly. <Ref. to
ME(H4SO 2.0)-30, REMOVAL, Engine Assembly.>
2) Remove the engine mounting from engine as-
sembly.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Engine mounting
35 N
⋅
m (3.6 kgf-m, 25.8 ft-lb)
C: INSPECTION
Make sure that no crack or other damages do not
exist.
ME(H4SO 2.0)-36
MECHANICAL
Preparation for Overhaul
11.Preparation for Overhaul
A: PROCEDURE
1) After removing the engine from body, secure it in
the ST shown below.
ST1
498457000
ENGINE STAND ADAPTER
RH
ST2
498457100
ENGINE STAND ADAPTER
LH
ST3
499817100
ENGINE STAND
2) In this section the procedures described under
each index are all connected and stated in order.
The procedure for overhauling of the engine will be
completed when you go through all steps in the
process.
Therefore, in this section, to conduct the particular
procedure within the flow of a section, you need to
go back and conduct the procedure described pre-
viously in order to do that particular procedure.
ME-00221
ST2
ST1
ST3
ME(H4SO 2.0)-37
MECHANICAL
V-belt
12.V-belt
A: REMOVAL
NOTE:
Perform the following procedures with the engine
installed to the body.
1. FRONT SIDE BELT
1) Remove the V-belt covers.
2) Loosen the lock bolt (A).
3) Loosen the slider bolt (B).
4) Remove the front side belt (C).
2. REAR SIDE BELT
1) Loosen the lock nut (A).
2) Loosen the slider bolt (B).
3) Remove the rear side belt.
4) Remove the belt tensioner.
B: INSTALLATION
NOTE:
Wipe off any oil or water on the belt and pulley.
1. FRONT SIDE BELT
1) Install the V-belt (C), and tighten the slider bolt
so as to obtain the specified belt tension. <Ref. to
ME(H4SO 2.0)-38, INSPECTION, V-belt.>
2) Tighten the lock bolt (A).
3) Tighten the slider bolt (B).
Tightening torque:
Lock bolt (A)
25 N
⋅
m (2.5 kgf-m, 18.4 ft-lb)
Slider bolt (B)
8 N
⋅
m (0.8 kgf-m, 5.8 ft-lb)
ME-00222
ME-00223
(B)
(C)
(A)
ME-00224
(A)
(B)
ME-00225
ME-00223
(B)
(C)
(A)
ME(H4SO 2.0)-38
MECHANICAL
V-belt
2. REAR SIDE BELT
1) Install the belt tensioner.
2) Install the V-belt, and tighten the slider bolt (B)
so as to obtain the specified belt tension.
<Ref. to ME(H4SO 2.0)-38, INSPECTION, V-belt.>
3) Tighten the lock nut (A).
Tightening torque:
Lock nut (A)
23 N
⋅
m (2.3 kgf-m, 17.0 ft-lb)
C: INSPECTION
1) Replace the belts, if crack, fraying or wear is
found.
2) Remove the V-belt cover and reservoir tank.
(with belt tension gauge)
3) Check the V-belt tension and adjust it if neces-
sary by changing the generator installing position
or idler pulley installing position.
Belt tension (with belt tension gauge):
Front side belt
When installing new parts
618 — 755 N (63 — 77 kgf, 139 — 170 lbf)
At inspection
490 — 640 N (50.0 — 65.3 kgf, 110.2 — 143.9
lbf)
Rear side belt
When installing new parts:
740 — 880 N (75.5 — 89.7 kgf, 166 — 198
lbf)
At inspection
350 — 450 N (35.7 — 45.9 kgf, 78.7 — 101.2
lbf)
ME-00224
(A)
(B)
(A) Front side belt
(B) Rear side belt
C/P Crank pulley
GEN Generator
P/S Power steering oil pump pulley
A/C Air conditioning compressor pulley
I/P Idler pulley
C/P
P/S
A/C
GEN
(A)
(B)
I/P
PM-00154
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст