Subaru Legacy (2005 year). Service manual — part 921
SB-5
SEAT BELT SYSTEM
General Description
4. REAR SEAT BELT (WAGON MODEL)
(1)
Outer seat belt RH ASSY
(5)
Center seat belt LH ASSY
Tightening torque: N
⋅
m (kgf-m, ft-lb)
(2)
Shoulder seat belt center ASSY
(6)
Outer belt guide RH
T1: 30 (3.1, 22)
(3)
Outer seat belt LH ASSY
(7)
Outer belt guide LH
T2: 53 (5.4, 39)
(4)
Center seat belt RH ASSY
SB-00148
(2)
(6)
(1)
(4)
(7)
T2
(5)
(3)
T1
T1
T1
T1
T1
SB-6
SEAT BELT SYSTEM
General Description
B: CAUTION
• Before starting service, turn the ignition switch to
OFF, disconnect the battery ground cable and wait
for 20 seconds or more.
• The pretensioner system has a backup power
source. The pretensioner might deploy if you do not
wait for 20 seconds or more before starting work.
• Do not drop or apply any impact to the preten-
sioner.
• If oil, grease or water gets on the pretensioner,
wipe it off immediately with a dry cloth.
• Do not expose the pretensioner to high tempera-
ture or flame.
• Do not allow current to flow through or voltage to
reach the pretensioner. Do not use a circuit tester
to check resistance of the pretensioner.
• Do not disassemble or attempt to repair the pre-
tensioner. If it is dented, cracked or deformed, re-
place it with a new one.
• Do not use the airbag or pretensioner parts from
other vehicles. Always replace the parts with new
ones.
• When handling a seat belt with deployed preten-
sioner, wear gloves and goggles. Wash your hands
afterwards.
• Do not reuse a seat belt with deployed preten-
sioner.
• If the material gets in your eyes or on your skin
during deployment, wash it away with clean water,
and then consult a doctor.
SB-7
SEAT BELT SYSTEM
General Description
C: PREPARATION TOOL
1. SPECIAL TOOL
2. GENERAL TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
98299SA010
DEPLOYMENT
ADAPTER D
• Used for deploying the pretensioner.
• Used with DEPLOYMENT TOOL
(98299PA030).
98299SA050
DEPLOYMENT
ADAPTER F
• Used for deploying the lap seat belt preten-
sioner.
• Used with DEPLOYMENT TOOL
(98299PA030).
98299PA030
DEPLOYMENT
TOOL
• Used for deploying the pretensioner.
• Used with DEPLOYMENT ADAPTER D
(98299SA010) or DEPLOYMENT ADAPTER F
(98299SA050).
TOOL NAME
REMARKS
TORX
®
T50
Used for removing and installing the inner seat belt assembly.
ST98299SA010
ST98299SA050
ST98299PA030
SB-8
SEAT BELT SYSTEM
Pretensioner Connector
2. Pretensioner Connector
A: REMOVAL
1) Using a flat tip screwdriver, pry the push lock up-
ward to unlock.
2) Pull out the connector to disconnect it from re-
tractor assembly.
B: INSTALLATION
Connect the connector in the reverse order of dis-
connection. At this time, be sure to insert the push
lock until a connecting sound is heard.
CAUTION:
• Be sure to insert the connector in until it is
locked. Then pull it gently to make sure that it is
locked.
• Be sure to push the push lock in securely.
AB-00478
AB-00479
AB-00480
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст