Subaru Legacy IV (2008 year). Service manual — part 1135
EI-39
Rear Bumper
EXTERIOR/INTERIOR TRIM
4. REAR BUMPER BEAM ASSEMBLY
1) Disconnect the ground cable from the battery.
2) Remove the rear bumper face. <Ref. to EI-37,
REAR BUMPER FACE (SEDAN MODEL), RE-
MOVAL, Rear Bumper.>
3) Remove the energy absorber foam.
4) Remove the nuts, and remove the beam main
reinforcement from the vehicle body.
5) Remove the nuts, and remove the bumper beam
bracket and beam upper rear from the vehicle
body.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
• When the side garnish is removed, replace the
double-sided tape with new one.
• If the bumper face comes off easily from the
beam upper rear, adjust the hook of the bracket
side.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”.
• Sedan model <Ref. to EI-6, REAR BUMPER
(SEDAN MODEL), COMPONENT, General De-
scription.>
• Wagon model <Ref. to EI-7, REAR BUMPER
(WAGON MODEL), COMPONENT, General
Description.>
C: REPAIR
Refer to the front bumper repair. <Ref. to EI-32,
REPAIR, Front Bumper.>
EI-00803
EI-00804
EI-40
Cowl Panel
EXTERIOR/INTERIOR TRIM
10.Cowl Panel
A: REMOVAL
1) Open the front hood.
2) Remove the wiper arm. <Ref. to WW-14, RE-
MOVAL, Front Wiper Arm.>
3) Remove the weather strip clips, and remove the
weather strip.
NOTE:
If the weather strip clip is removed with excessive
force, the weather strip may be damaged. Be sure
to use a clip remover to remove.
4) Remove the clip, and remove the cover cowl
panel.
5) Remove the cowl panel side and clip (A).
6) Remove the clips (A), and remove the cowl pan-
el.
B: INSTALLATION
Install in the reverse order of removal.
EI-00642
EB-00141
EI-00643
EI-00790
(A)
:(A)
EI-00644
EI-41
Roof Spoiler
EXTERIOR/INTERIOR TRIM
11.Roof Spoiler
A: REMOVAL
1) Disconnect the ground cable from the battery.
2) Remove the rear gate trim. <Ref. to EI-68, RE-
MOVAL, Rear Gate Trim.>
3) Disconnect the connector of high-mounted stop
light and the washer hose of rear washer.
4) Remove the nut and plastic caps.
5) Remove the clips, and remove the roof spoiler.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
4.5 N·m (0.46 kgf-m, 3.32 ft-lb)
EI-00828
EI-00646
EI-42
Side Sill Spoiler
EXTERIOR/INTERIOR TRIM
12.Side Sill Spoiler
A: REMOVAL
Remove the clips (two in the front fender arch, six for side sill spoiler lower area), and remove the side spoiler.
NOTE:
When peeling the double sided tape, refer to removal procedures for the side protector. <Ref. to EI-44, RE-
MOVAL, Side Protector.>
(A)
Yellow clip
(B)
Green clip
(C)
Black clip
(1)
Side sill spoiler
(3)
End cover
(4)
Clip
(2)
Double-sided
tape
EI-01083
(1)
(2)
(3)
(C)
(A)
(B)
(A)
(A)
(A)
(4)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст