Subaru Legacy IV (2008 year). Service manual — part 1132
EI-27
Floor Under Protector
EXTERIOR/INTERIOR TRIM
5. Floor Under Protector
A: REMOVAL
1) Lift up the vehicle.
NOTE:
A plate type lift cannot be used.
2) Remove the push turn clips (A) and bolts (B),
and remove the floor under protector.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to EI-3, UNDER PROTECTOR,
COMPONENT, General Description.>
EI-00637
(A)
(A)
(B)
(A)
(B)
(A)
(A)
(B)
(A)
(A)
(A)
(A)
(A)
EI-28
Fuel Tank Protector
EXTERIOR/INTERIOR TRIM
6. Fuel Tank Protector
A: REMOVAL
1) Lift up the vehicle.
2) Remove the bolts (A) and nuts (B), and then re-
move the fuel tank protector.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to EI-3, UNDER PROTECTOR,
COMPONENT, General Description.>
EI-00638
(B)
(B)
(A)
(A)
(B)
(B)
(A)
(A)
(A)
(A)
EI-29
Mud Guard
EXTERIOR/INTERIOR TRIM
7. Mud Guard
A: REMOVAL
1. FRONT MUD GUARD
1) Jack-up the vehicle.
2) Remove the front wheels.
3) Loosen the screws and clips to remove mud
guard.
2. REAR MUD GUARD
1) Jack-up the vehicle.
2) Remove the rear wheels.
3) Loosen the screws and clips to remove the mud
guard.
B: INSTALLATION
Install in the reverse order of removal.
EI-01758
EI-00640
EI-30
Front Bumper
EXTERIOR/INTERIOR TRIM
8. Front Bumper
A: REMOVAL
1. FRONT BUMPER FACE
1) Disconnect the ground cable from the battery.
2) Remove the upper side clip of the front grille.
3) Turn over the front mud guard, and remove the
clips connecting the fender and bumper.
4) Remove the clips at the lower side of bumper.
NOTE:
Remove the under cover to facilitate the work.
<Ref. to EI-26, REMOVAL, Front Under Cover.>
5) Turn over the mud guard and disconnect the fog
light connector. (Model with fog light)
6) For OUTBACK model, remove the front fender
side garnish.
NOTE:
To remove the side garnish claw (A) from the
bumper face.
7) Detach the flange sections on the bumper face
side from guide bracket (A).
CAUTION:
Do not pull forcibly. Doing so can damage the
flange on the bumper face.
NOTE:
It is easier to detach them from the fender side in
the order from (1) to (3), while pulling up the
bumper face to the direction of arrow (B) (upward).
8) Remove the bumper face from vehicle body.
9) Remove the fog light from bumper face. <Ref. to
LI-19, REMOVAL, Front Fog Light Assembly.>
10) Remove the front grille assembly from bumper
face. <Ref. to EI-24, REMOVAL, Front Grille.>
EI-00572
EI-01753
EI-01726
(A)
EI-01723
(1)
(2)
(3)
(B)
(A)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст