Subaru Legacy IV (2008 year). Service manual — part 781
5MT-20
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
899904100
REMOVER
Used for removing and installing the straight pin.
899988608
SOCKET WRENCH
(27)
Used for removing and installing the drive pinion
lock nut.
398497701
ADAPTER
• Used for installing roller bearing onto the differ-
ential case.
• Used together with the BUSHING 1-2
INSTALLER (499277100).
499587000
INSTALLER
Used for installing the driven gears to the driven
shaft.
498057300
INSTALLER
Used for installing the extension oil seal.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-899904100
ST-899988608
ST-398497701
ST-499587000
ST-498057300
5MT-21
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
498255400
PLATE
Used for measuring backlash.
41099AC000
ENGINE SUPPORT
ASSY
Used for supporting the engine.
398527700
PULLER ASSY
Used for removing the extension case roller
bearing.
398643600
GAUGE
Used for measuring the total end play, extension
end play and drive pinion height.
398177700
INSTALLER
• Used for installing the bearing cone of transfer
driven gear (transfer case side).
• Used for installing the ball bearing of the trans-
fer drive gear.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-498255400
ST41099AC000
ST-398527700
ST-398643600
ST-398177700
5MT-22
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
2. GENERAL TOOL
28399SA010
OIL SEAL
PROTECTOR
Used for protecting the oil seal from damage
when inserting the front drive shaft.
18675AA000
DIFFERENTIAL
SIDE OIL SEAL
INSTALLER
Used for installing the differential side retainer oil
seal.
398791700
STRAIGHT PIN
REMOVER 2
Used for installing and removing the straight pin.
TOOL NAME
REMARKS
Circuit tester
Used for measuring resistance, voltage and current.
TORX
®
bit T70
Used for installing and removing the differential gear oil drain plug.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST28399SA010
ST18675AA000
ST-398791700
5MT-23
Transmission Gear Oil
MANUAL TRANSMISSION AND DIFFERENTIAL
2. Transmission Gear Oil
A: INSPECTION
1) Park the vehicle on a level surface.
2) Turn the ignition switch to OFF, and wait until the
engine cools.
3) Remove the oil level gauge and wipe it clean.
4) Reinsert the oil level gauge all the way. Be sure
that the oil level gauge is correctly inserted in the
proper direction.
5) Pull out the oil level gauge again, and check the
oil level. If it is at the lower level or less, add oil
through the oil level gauge hole to bring the level up
to the upper level.
B: REPLACEMENT
1) Pull out the oil level gauge.
2) Lift up the vehicle.
3) Using the TORX
®
bit T70, remove the drain
plug, and drain the transmission gear oil complete-
ly.
CAUTION:
• Immediately after the engine has been run-
ning, the transmission gear oil will be hot. Be
careful not to burn yourself.
• Be careful not to spill the transmission gear
oil on exhaust pipe to prevent it from emitting
smoke or causing fires. If gear oil is spilled,
wipe it off completely.
4) Using the TORX
®
bit T70, tighten the transmis-
sion gear oil drain plug.
NOTE:
• Tighten the drain plug of the transmission gear
oil after draining the transmission gear oil.
• Use a new gasket.
Tightening torque:
44 N·m (4.5 kgf-m, 32.5 ft-lb) (Aluminum gas-
ket)
70 N·m (7.1 kgf-m, 51.6 ft-lb) (Copper gasket)
5) Lower the vehicle.
6) Pour gear oil through the oil level gauge hole.
Recommended gear oil:
GL-5 (75W-90) or equivalent
Gear oil capacity:
3.5
2
(3.7 US qt, 3.1 Imp qt)
7) Measure the transmission gear oil amount, and
check that it is within the specification.
CAUTION:
When inserting the oil level gauge into the
transmission, align the protrusion on top of the
oil level gauge with the notch in the oil level
gauge hole.
(A) Oil level gauge
(B) Upper level
(C) Lower level
PM-00030
(B)
(C)
(A)
MT-01548
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст