Subaru Legacy IV (2008 year). Service manual — part 30
FU(H4SO)-9
General Description
FUEL INJECTION (FUEL SYSTEMS)
(1)
Clip
(17)
Drain valve
(33)
Connector B
(2)
Fuel damper
(18)
Drain filter
(34)
Canister hose B
(3)
Evaporation hose A
(19)
Canister protector
(35)
Drain hose
(4)
Fuel delivery hose A
(20)
Pressure control solenoid valve
(36)
Drain hose connector
(5)
Fuel delivery hose B
(21)
Evaporation pipe A
(37)
Evaporation hose C
(6)
Clip
(22)
Evaporation pipe B
(38)
Evaporation hose D
(7)
Bracket
(23)
Clip
(39)
Evaporation hose E
(8)
Evaporation tube
(24)
Fuel filler pipe
(9)
Fuel pipe ASSY A
(25)
Shut valve
Tightening torque:N·m (kgf-m, ft-lb)
(10)
Fuel delivery hose C
(26)
Gasket
T1: 4.4 (0.4, 3.2)
(11)
Retainer
(27)
Filler ring
T2: 7.5 (0.8, 5.5)
(12)
Evaporation hose B
(28)
Fuel filler cap
T3: 8 (0.8, 5.9)
(13)
Clamp
(29)
Fuel tank pressure sensor
T4: 17.6 (1.8, 13)
(14)
Grommet
(30)
Evaporation pipe protector
T5: 1.25 (0.1, 0.9)
(15)
Fuel pipe ASSY B
(31)
Connector A
T6: 1 (0.1, 0.7)
(16)
Canister
(32)
Canister hose A
FU(H4SO)-10
General Description
FUEL INJECTION (FUEL SYSTEMS)
6. FUEL PUMP
(1)
Sub tank bracket ASSY
(6)
Fuel filter
(10)
Sub tank
(2)
O-ring
(7)
Clip
(11)
Cushion
(3)
O-ring
(8)
Spacer
(12)
Fuel level sensor
(4)
Fuel pump harness
(9)
Pump ASSY
(13)
Fuel temperature sensor
(5)
Spring
(1)
(4)
(5)
(6)
(2)
(8)
(9)
(10)
(11)
(7)
FU-04005
b
C
d
d
(2)
(2)
(3)
(5)
a
b
C
(12)
a
(13)
FU(H4SO)-11
General Description
FUEL INJECTION (FUEL SYSTEMS)
C: CAUTION
• Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing
any work.
• Remove contamination including dirt and corrosion before removal, installation or disassembly.
• Keep the disassembled parts in order and protect them from dust and dirt.
• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, in-
stallation, disassembly and replacement.
• Vehicle components are extremely hot after driving. Be wary of receiving burns from heated parts.
• Be sure to tighten fasteners including bolts and nuts to the specified torque.
• Place shop jacks or rigid racks at the specified points.
• Before disconnecting connectors of sensors or units, be sure to disconnect the ground cable from the bat-
tery.
• Place “NO OPEN FLAMES” signs near the working area.
• Prepare a container and cloth to prevent scattering of fuels when performing work where fuels can be
spilled. If the fuel spills, wipe it off immediately to prevent from penetrating into floor or flowing out for envi-
ronmental protection.
• Follow all government and local regulations concerning disposal of refuse when disposing fuel.
D: PREPARATION TOOL
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
42099AE000
QUICK
CONNECTOR
RELEASE
Used for removing the quick connector.
18471AA000
FUEL PIPE
ADAPTER
Used for draining fuel.
1B022XU0
SUBARU SELECT
MONITOR III KIT
Used for draining fuel.
ST42099AE000
ST18471AA000
ST1B022XU0
FU(H4SO)-12
Throttle Body
FUEL INJECTION (FUEL SYSTEMS)
2. Throttle Body
A: REMOVAL
1) Set the vehicle on a lift.
2) Disconnect the ground cable from battery.
3) Lift up the vehicle.
4) Remove the under cover.
5) Drain approximately 3.0
2 (3.2 US qt, 2.6 Imp
qt) of coolant. <Ref. to CO(H4SO)-13, DRAINING
OF ENGINE COOLANT, REPLACEMENT, Engine
Coolant.>
6) Remove the air intake chamber. <Ref. to
IN(H4SO)-7, REMOVAL, Air Intake Chamber.>
7) Disconnect the throttle position sensor connec-
tor (A) and manifold absolute pressure sensor con-
nector (B).
8) Disconnect the engine coolant hoses (A) from
the throttle body.
9) Remove the bolts (B) which secure the throttle
body to the intake manifold, and remove the throttle
body.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Use a new gasket.
Tightening torque:
8 N·m (0.8 kgf-m, 5.9 ft-lb)
IN-00203
FU-03448
(B)
(A)
FU-01084
(B)
(A)
(A)
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст