Subaru Legacy IV (2008 year). Service manual — part 764
5AT(diag)-71
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
V: DTC P0763 SHIFT SOLENOID “C” ELECTRICAL
DTC DETECTING CONDITION:
Output signal circuit of high & low reverse clutch linear solenoid is open or shorted.
TROUBLE SYMPTOM:
Locked to 1st gear.
WIRING DIAGRAM:
Step
Check
Yes
No
1
CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
transmission.
3) Measure the resistance of harness between
TCM and transmission connector.
Connector & terminal
(B55) No. 22 — Chassis ground:
(B55) No. 23 — Chassis ground:
(B54) No. 5 — (B11) No. 15:
Is the resistance less than 1
:? Go to step 2.
Repair the open
circuit of harness
between TCM con-
nector and trans-
mission connector.
2
CHECK HARNESS CONNECTOR BETWEEN
TCM AND CHASSIS GROUND.
Measure the resistance of harness between
TCM connector and chassis ground.
Connector & terminal
(B54) No. 5 — Chassis ground:
Is the resistance 1 M
: or
more?
Go to step 3.
Repair the short
circuit of harness
between TCM con-
nector and trans-
mission connector.
A5
2
B11
T4
15
T11
B11
1
2
3 4
5
6 7
8
9
13
14 15
20
19
17
16
10
11 12
18
5
6
7 8
2
1
9
4
3
10
24
22 23
25
11 12 13 14 15
26 27
28
16
17 18 19 20 21
33 34
29
32
30
31
35
1 2 3 4
5 6 7 8
T11
5
6
7
2
1
3
4
29
10 11 12 13 14 15
25
24
16
30
9
8
17 18 19
20
28
21 22 23
32
31
26 27
33
34 35
TCM
B54
A:
B55
B:
B22
B23
E
B54
A:
B55
B:
AT-04359
CONTROL VALVE BODY
HIGH & LOW
REVERSE CLUTCH
LINEAR SOLENOID
5AT(diag)-72
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
3
CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND CONTROL VALVE
BODY.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmis-
sion.
3) Remove the transmission connector from
bracket.
4) Lift up the vehicle.
NOTE:
Raise all wheels off the floor.
5) Drain the ATF.
CAUTION:
Do not drain ATF until it cools down.
6) Remove the oil pan, and disconnect the
control valve body connector.
7) Measure the resistance between transmis-
sion connector and control valve body connec-
tor.
Connector & terminal
(T4) No. 15 — (T11) No. 2:
Is the resistance less than 1
:? Go to step 4.
Repair the open
circuit of harness
between transmis-
sion connector and
control valve body
connector.
4
CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND CONTROL VALVE
BODY.
Measure the resistance of harness connector
between control valve body connector and
transmission ground.
Connector & terminal
(T11) No. 2 — Transmission ground:
Is the resistance 1 M
: or
more?
Repair the open
circuit of harness
between control
valve body con-
nector and trans-
mission ground.
Go to step 5.
5
CHECK HIGH & LOW REVERSE CLUTCH
LINEAR SOLENOID.
Measure the resistance between transmission
ground and control valve body connector.
Connector & terminal
(T11) No. 2 — Transmission ground:
Is the resistance 3 — 9
:?
Go to step 6.
Replace the con-
trol valve body.
<Ref. to 5AT-57,
Control Valve
Body.>
6
CHECK POOR CONTACT.
Check that there are no poor contact in TCM
connector, transmission connector and control
valve body connector.
Is there any loosing terminal,
entering foreign matter, damag-
ing connector body?
Repair the poor
contact.
Go to step 7.
7
CHECK AFTER REPAIR.
1) Perform the Clear Memory Mode.
2) Drive for a while, read the DTC, and check
that there is no faulty.
Is DTC displayed?
Replace the TCM.
<Ref. to 5AT-60,
Transmission Con-
trol Module
(TCM).>
Temporary poor
contact or open cir-
cuit occurs.
Recheck that the
harness connector
has no faulty.
Step
Check
Yes
No
5AT(diag)-73
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
W: DTC P0766 SHIFT SOLENOID “D” PERFORMANCE OR STUCK OFF
DTC DETECTING CONDITION:
Output signal value of direct clutch linear solenoid does not match the oil pressure.
TROUBLE SYMPTOM:
Locked to 1st or 4th gear.
WIRING DIAGRAM:
Step
Check
Yes
No
1
CHECK HARNESS CONNECTOR BETWEEN
TCM AND TRANSMISSION.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from TCM and
transmission.
3) Measure the resistance of harness between
TCM and transmission connector.
Connector & terminal
(B55) No. 22 — Chassis ground:
(B55) No. 23 — Chassis ground:
(B54) No. 1 — (B11) No. 16:
(B54) No. 22 — (B11) No. 10:
Is the resistance less than 1
:? Go to step 2.
Repair the open
circuit of harness
between TCM and
transmission con-
nector.
2
CHECK HARNESS CONNECTOR BETWEEN
TCM AND BODY HARNESS.
Measure the resistance of harness between
TCM connector and body harness.
Connector & terminal
(B54) No. 22 — Chassis ground:
Is the resistance 1 M
: or
more?
Go to step 3.
Repair the short
circuit of harness
between TCM and
transmission con-
nector.
3
CHECK INPUT SIGNAL FOR TCM USING
SUBARU SELECT MONITOR.
1) Connect all connectors.
2) Turn the ignition switch to ON. (engine OFF)
3) Check input signal of “D/C oil pressure SW”.
Is OFF displayed?
Go to step 4.
Go to step 6.
AT-04360
A22
A1
CONTROL VALVE BODY
B11
T4
9
4
T10
T11
16
10
DIRECT CLUTCH
OIL PRESSURE
SWITCH
DIRECT CLUTCH
LINEAR
SOLENOID
B11
1 2
5
6 7
8
13
14 15
16
9 10
11 12
3 4
17 18
19 20
T11
1 2 3 4
5 6 7 8
16
10 11 12 13 14 15
25
24
30
9
8
7
17 18 19 20
28
21 22 23
29
32
31
1
2
3
4
5
6
27
26
33 34 35
T10
1 2 3 4
6 7 8 9
5
10
5
6
7
2
1
3
4
29
10 11 12 13 14 15
25
24
16
30
9
8
17 18 19
20
28
21 22 23
32
31
26 27
33
34 35
TCM
B54
A:
B55
B:
B22
B23
E
B54
A:
B55
B:
5AT(diag)-74
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
AUTOMATIC TRANSMISSION (DIAGNOSTICS)
4
CHECK INPUT SIGNAL FOR TCM USING
SUBARU SELECT MONITOR.
1) Turn the ignition switch to OFF.
2) Turn the ignition switch to ON. (Engine ON)
3) Shift to 2nd speed of manual mode and
brake ON with checking current gear position
using Subaru Select Monitor.
4) Check input signal of “D/C oil pressure SW”.
Is ON displayed?
Even if the AT OIL
TEMP light blinks,
the system is in
normal condition.
A temporary poor
contact of connec-
tor or harness may
be the cause.
Repair the poor
contact of harness
in the solenoid out-
put and oil pres-
sure SW input.
Go to step 5.
5
CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND CONTROL VALVE
BODY.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmis-
sion.
3) Remove the transmission connector from
bracket.
4) Lift up the vehicle.
NOTE:
Raise all wheels off the floor.
5) Drain the ATF.
CAUTION:
Do not drain ATF until it cools down.
6) Remove the oil pan, and disconnect the
control valve body connector.
7) Measure the resistance between transmis-
sion connector and control valve body connec-
tor.
Connector & terminal
(T4) No. 16 — (T11) No. 4:
(T4) No. 10 — (T10) No. 9:
Is the resistance less than 1
:? Replace the con-
trol valve body.
<Ref. to 5AT-57,
Control Valve
Body.>
Replace the trans-
mission harness
assembly.
6
CHECK HARNESS CONNECTOR BETWEEN
TRANSMISSION AND CONTROL VALVE
BODY.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from transmis-
sion.
3) Remove the transmission connector from
bracket.
4) Lift up the vehicle.
NOTE:
Raise all wheels off the floor.
5) Drain the ATF.
CAUTION:
Do not drain ATF until it cools down.
6) Remove the oil pan, and disconnect the
control valve body connector.
7) Check the insulation of transmission har-
ness assembly.
Connector & terminal
(T10) No. 9 — Transmission ground:
Is the resistance 1 M
: or
more?
Replace the con-
trol valve body.
<Ref. to 5AT-57,
Control Valve
Body.>
Replace the trans-
mission harness
assembly.
Step
Check
Yes
No
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст