Subaru Legacy IV (2008 year). Service manual — part 1114
SL-29
Security System
SECURITY AND LOCKS
NOTE:
Check the function settings of the body integrated unit if any of the following symptoms appear. <Ref. to
LAN(diag)-2, Basic Diagnostic Procedure.>
• The horn does not sound even when the security system operates. (Siren YES/NO)
• The horn sounds when setting the security to ON using the keyless transmitter. (Impact sensor YES/NO)
2. CHECK SECURITY SYSTEM CONDITION MEMORY
1) Remove the key from ignition switch.
2) Close all the doors, trunk lid and rear gate.
3) Open the front hood.
4) Press the LOCK button of transmitter, and then wait until the security indicator light flashes twice for 0.5
sec. at intervals of 2 seconds.
5) Disconnect the ground cable from the battery.
6) Connect the ground cable to the battery.
7) Check that the security indicator light blinks twice within 0.5 seconds at 2 second intervals. When it does
not blink, replace the body integrated unit.
3. SECURITY SYSTEM ON/OFF SETTING
1) Close all doors, trunk lid and rear gate, and sit down on the driver seat. Press the UNLOCK button of the
keyless transmitter.
2) Turn the ignition switch to ON.
3) Push the centralized door unlock switch down and open the driver’s side door at the same time, and hold
in this condition for 10 seconds.
4) If the security system is ON, it will turn OFF. If OFF, it will turn ON.
10
CHECK SECURITY ALARM CANCEL OPER-
ATION.
Press any button of transmitter while operating
security alarm. Or turn the ignition switch to
OFF
o ON once.
Does all security alarm stop?
• Horn
• Hazard light
Go to step 11.
Check the ignition
switch circuit.
<Ref. to SL-33,
CHECK IGNITION
SWITCH CIRCUIT,
INSPECTION,
Security System.>
11
CHECK SECURITY SYSTEM CONDITION
MEMORY.
Check that the system functions properly even
when the battery is not connected temporarily.
<Ref. to SL-29, CHECK SECURITY SYSTEM
CONDITION MEMORY, INSPECTION, Secu-
rity System.>
Does the system function prop-
erly when the battery is not con-
nected temporarily?
Go to step 12.
Replace the body
integrated unit.
<Ref. to SL-56,
Body Integrated
Unit.>
12
CHECK IMPACT SENSOR.
Check the sensibility of impact sensor. <Ref. to
SL-53, CHECK IMPACT SENSOR, ADJUST-
MENT, Impact Sensor.>
Is the sensibility set properly?
Press the
UNLOCK button of
keyless transmit-
ter, and finish the
diagnosis.
Adjust the sensitiv-
ity. <Ref. to SL-53,
IMPACT SENSI-
TIVITY ADJUST-
MENT,
ADJUSTMENT,
Impact Sensor.>
Step
Check
Yes
No
SL-30
Security System
SECURITY AND LOCKS
4. CHECK DOOR SWITCH
Step
Check
Yes
No
1
CHECK INPUT FROM EACH DOOR SWITCH.
1) Prepare the Subaru Select Monitor kit.
2) Turn the ignition switch to ON (engine OFF)
and run the “PC application for Subaru Select
Monitor”.
3) On the «System Selection Menu» display,
select the {Integ. unit mode}.
4) Select the {Current Data Display & Save}.
5) Check the door switch input to the body inte-
grated unit when opening the each door (front
RH and LH, rear RH and LH).
Does the display switch
between OFF
ON when
opening the each door (front
RH and LH, rear RH and LH)?
The door switch
circuit is OK.
Go to step 2.
2
CHECK DOOR SWITCH CIRCUIT.
1) Turn the ignition switch to OFF.
2) Disconnect the harness connector of body
integrated unit.
3) Disconnect the harness connector of faulty
door switch.
4) Measure the resistance between harness
connector terminals.
Connector & terminal
(i84) No. 19 — (R9) No. 1: (front door LH)
(i84) No. 32 — (R12) No. 1: (front door RH)
(i84) No. 31 — (R22) No. 1: (rear door LH)
(i84) No. 18 — (R16) No. 1: (rear door RH)
Is the resistance less than 10
:? Go to step 3.
Repair or replace
the harness.
3
CHECK GROUND CIRCUIT OF DOOR
SWITCH.
1) Disconnect the harness connector of faulty
door switch.
2) Measure the resistance of harness connec-
tor and chassis ground.
Connector & terminal
(R9) No. 3 — Chassis ground:
(front door LH)
(R12) No. 3 — Chassis ground:
(front door RH)
(R22) No. 3 — Chassis ground:
(rear door LH)
(R16) No. 3 — Chassis ground:
(rear door RH)
Is the resistance less than 10
:? Go to step 4.
Repair or replace
the harness.
4
CHECK DOOR SWITCH.
1) Disconnect the harness connector of faulty
door switch.
2) Measure the resistance between door
switch terminals.
Terminals
No. 1 — No. 3:
Is the resistance 1 M
: or more
when door switch is pushed?
Go to step 5.
Replace the door
switch.
5
CHECK DOOR SWITCH.
Measure the resistance between door switch
terminals.
Terminals
No. 1 — No. 3:
Is the resistance less than 1
:
when door switch is released?
Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
Replace the door
switch.
SL-31
Security System
SECURITY AND LOCKS
5. CHECK TRUNK LID SWITCH (SEDAN) OR REAR GATE LATCH SWITCH (WAGON)
Step
Check
Yes
No
1
CHECK INPUT FROM TRUNK LID SWITCH
OR REAR GATE LATCH SWITCH.
1) Prepare the Subaru Select Monitor kit.
2) Turn the ignition switch to ON (engine OFF)
and run the “PC application for Subaru Select
Monitor”.
3) On the «System Selection Menu» display,
select the {Integ. unit mode}.
4) Select the {Current Data Display & Save}.
5) Check the input signal to the body inte-
grated unit when opening the trunk lid or rear
gate.
Does the display switch
between OFF
ON when
trunk lid or rear gate is opened?
The trunk lid switch
or rear gate latch
switch circuit is
OK.
Go to step 2.
2
CHECK CIRCUIT FOR TRUNK LID SWITCH
OR REAR GATE LATCH SWITCH.
1) Turn the ignition switch to OFF.
2) Disconnect the harness connector of body
integrated unit.
3) Disconnect the harness connector of the
trunk lid switch or the rear gate latch switch.
4) Measure the resistance between harness
connector terminals.
Connector & terminal
(i84) No. 17 — (D46) No. 2: (Wagon model)
(i84) No. 17 — (R186) No. 3:
(Sedan model)
Is the resistance less than 10
:? Go to step 3.
Repair or replace
the harness.
3
CHECK GROUND CIRCUIT OF TRUNK LID
SWITCH OR REAR GATE LATCH SWITCH.
1) Disconnect the harness connector of the
trunk lid switch or the rear gate latch switch.
2) Measure the resistance between harness
connector terminal and chassis ground.
Connector & terminal
(D46) No. 1 — Chassis ground:
(Wagon model)
(R186) No. 1 — Chassis ground:
(Sedan model)
Is the resistance less than 10
:? Go to step 4.
Repair or replace
the harness.
4
CHECK TRUNK LID SWITCH OR REAR
GATE LATCH SWITCH.
1) Disconnect the harness connector of the
trunk lid switch or the rear gate latch switch.
2) Measure the resistance between switch ter-
minals.
Terminals
No. 1 — No. 2: (Wagon model)
No. 1 — No. 3: (Sedan model)
Is the resistance 1 M
: or more
when switch is pushed?
Go to step 5.
Replace the trunk
lid lock assembly
or rear gate latch
assembly.
5
CHECK TRUNK LID SWITCH OR REAR
GATE LATCH SWITCH.
Measure the resistance between switch termi-
nals.
Terminals
No. 1 — No. 2: (Wagon model)
No. 1 — No. 3: (Sedan model)
Is the resistance less than 1
:
when switch is released?
Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
Replace the trunk
lid lock assembly
or rear gate latch
assembly.
SL-32
Security System
SECURITY AND LOCKS
6. CHECK SECURITY INDICATOR LIGHT CIRCUIT
7. CHECK HORN
8. CHECK HAZARD LIGHT OPERATION
Refer to the hazard light operation check of the Keyless Entry System. <Ref. to SL-22, CHECK HAZARD
LIGHT OPERATION, INSPECTION, Keyless Entry System.>
Step
Check
Yes
No
1
CHECK SECURITY INDICATOR LIGHT.
1) Turn the ignition switch to OFF.
2) Disconnect the harness connector of body
integrated unit.
3) Connect the resistor (100
:) between body
integrated unit harness connector terminal (i84)
No. 33 and chassis ground.
Connector & terminal
(i84) No. 33 — Chassis ground:
Does the security indicator light
illuminate?
Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
Go to step 2.
2
CHECK POWER SUPPLY FOR SECURITY
INDICATOR LIGHT.
1) Disconnect the connector from the combi-
nation meter.
2) Measure the voltage between the combina-
tion meter harness connector terminal and
chassis ground.
Connector & terminal
(i10) No. 1 (+) — Chassis ground (–):
Is the voltage 10 V or more?
Go to step 3.
Check the harness
for open or short
circuits between
combination meter
and fuse.
3
CHECK SECURITY INDICATOR LIGHT CIR-
CUIT.
Measure the resistance between the combina-
tion meter harness connector terminal and the
security control unit harness connector termi-
nal.
Connector & terminal
(i10) No. 17 — (i84) No. 33:
Is the resistance less than 10
:? Replace the com-
bination meter.
<Ref. to IDI-22,
Combination
Meter.>
Check the harness
for open or short
circuits between
the combination
meter and body
integrated unit.
Step
Check
Yes
No
1
CHECK HORN OPERATION.
Check the horn sounds when the horn switch is
pushed.
Does the horn sound?
Go to step 2.
Check the horn cir-
cuit. <Ref. to COM-
5, Horn Switch.>
2
CHECK OUTPUT TO HORN RELAY.
1) Prepare the Subaru Select Monitor kit.
2) Turn the ignition switch to ON (engine OFF)
and run the “PC application for Subaru Select
Monitor”.
3) On the «System Selection Menu» display,
select the {Integ. unit mode}.
4) Select {Function check}.
5) Select {Horn Output} and execute
Does the horn sound?
Horn circuit is OK. Go to step 3.
3
CHECK HORN RELAY CIRCUIT.
1) Turn the ignition switch to OFF.
2) Disconnect the harness connector of body
integrated unit.
3) Disconnect the main fuse box harness con-
nector (B186).
4) Measure the resistance between harness
connector terminals.
Connector & terminal
(B280) No. 11 — (B186) No. 1:
Is the resistance less than 10
:? Check the body
integrated unit.
<Ref. to
LAN(diag)-2, Basic
Diagnostic Proce-
dure.>
Repair or replace
the harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст