Subaru Legacy IV (2008 year). Service manual — part 307
EN(H4DOTC)(diag)-49
Drive Cycle
ENGINE (DIAGNOSTICS)
3. DRIVE CYCLE B — 10 MINUTES IDLING
NOTE:
Drive the vehicle at 10 km/h (6 MPH) or faster before diagnosis.
4. DRIVE CYCLE C — DRIVE THE VEHICLE WITH FOLLOWING DRIVE PATTERNS
DTC
Item
Condition
*P0171
System Too Lean (Bank 1)
Complete diagnosis with drive cycle A or C as well.
*P0172
System Too Rich (Bank 2)
Complete diagnosis with drive cycle A or C as well.
*P0301
Cylinder 1 Misfire Detected
Complete diagnosis with drive cycle A or C as well.
*P0302
Cylinder 2 Misfire Detected
Complete diagnosis with drive cycle A or C as well.
*P0303
Cylinder 3 Misfire Detected
Complete diagnosis with drive cycle A or C as well.
*P0304
Cylinder 4 Misfire Detected
Complete diagnosis with drive cycle A or C as well.
*P0464
Fuel Level Sensor Circuit Intermittent
—
*P0506
Idle Air Control System RPM Lower Than Expected
—
*P0507
Idle Air Control System RPM Higher Than Expected
—
*P2096
Post Catalyst Fuel Trim System Too Lean (Bank 1)
Complete diagnosis with drive cycle A or C as well.
*P2097
Post Catalyst Fuel Trim System Too Rich (Bank 1)
Complete diagnosis with drive cycle A or C as well.
P2103
Throttle Actuator Control Motor Circuit High
Complete diagnosis with drive cycle A or C as well.
(A)
Idle the engine for 10 seconds or
more.
(D)
Decelerate the vehicle to 64 km/h
(40 MPH) with throttle fully closed.
(G)
Stop the vehicle with throttle fully
closed.
(B)
Accelerate the vehicle to 97 km/h
(60 MPH) within 20 seconds.
(E)
Drive the vehicle at 64 km/h
(40 MPH) for 20 seconds.
(H)
Vehicle speed km/h (MPH)
(I)
Sec.
(C)
Drive the vehicle at 97 km/h (60
MPH) for 20 seconds.
(F)
Accelerate the vehicle to 97 km/h
(60 MPH) within 10 seconds.
EN-00842
(C)
(H)
(I)
(60)
97
64 (40)
(B)
(A)
(F)
(D)
(E)
150
100
50
0
(G)
EN(H4DOTC)(diag)-50
Drive Cycle
ENGINE (DIAGNOSTICS)
5. DRIVE CYCLE D
DRIFT DIAGNOSIS
1) Make sure that the engine coolant temperature at engine starting is less than 30°C (86°F).
2) Make sure that fuel remains 10
2 (2.6 US gal, 2.2 Imp gal) or more and the battery voltage is 10.9 V or
more.
3) Start the engine, and check that the engine coolant temperature increases by 10°C (18°F) or more, and
reaches 75°C (167°F) or more, when the engine is warmed up.
4) After the engine has reached the state of procedure 3), idle the engine for 120 seconds or more.
STUCK DIAGNOSIS
1) Make sure that the battery voltage is 10.9 V or more.
2) Perform the Clear Memory Mode. <Ref. to EN(H4DOTC)(diag)-52, Clear Memory Mode.>
3) Drive for approximately 50
2 (13.2 US gal, 11 Imp gal) of fuel.
NOTE:
• It is acceptable to drive the vehicle intermittently.
• Do not disconnect the battery terminals while diagnosing. (Data will be cleared by disconnecting the bat-
tery terminals.)
6. DRIVE CYCLE E
1) Make sure that the battery voltage is 10.9 V or more.
2) Perform the Clear Memory Mode. <Ref. to EN(H4DOTC)(diag)-52, Clear Memory Mode.>
3) Drive for approximately 30
2 (7.9 US gal, 6.6 Imp gal) of fuel.
NOTE:
• It is acceptable to drive the vehicle intermittently.
• Do not disconnect the battery terminals while diagnosing. (Data will be cleared by disconnecting the bat-
tery terminals.)
DTC
Item
Condition
*P0030
HO2S Heater Control Circuit (Bank 1 Sensor 1)
—
*P0068
MAP/MAF - Throttle Position Correlation
—
*P0101
Mass or Volume Air Flow Circuit Range/Performance
—
P0134
O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
—
*P0139
O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)
—
*P0171
System Too Lean (Bank 1)
Complete diagnosis with drive cycle A or B as well.
*P0172
System Too Rich (Bank 2)
Complete diagnosis with drive cycle A or B as well.
P0244
Turbo/Super Charger Wastegate Solenoid “A” Range/Performance
—
P0246
Turbo/Super Charger Wastegate Solenoid “A” High
—
*P0301
Cylinder 1 Misfire Detected
Complete diagnosis with drive cycle A or B as well.
*P0302
Cylinder 2 Misfire Detected
Complete diagnosis with drive cycle A or B as well.
*P0303
Cylinder 3 Misfire Detected
Complete diagnosis with drive cycle A or B as well.
*P0304
Cylinder 4 Misfire Detected
Complete diagnosis with drive cycle A or B as well.
P2004
Intake Manifold Runner Control Stuck Open (Bank 1)
—
P2005
Intake Manifold Runner Control Stuck Open (Bank 2)
—
*P2096
Post Catalyst Fuel Trim System Too Lean (Bank 1)
Complete diagnosis with drive cycle A or B as well.
*P2097
Post Catalyst Fuel Trim System Too Rich (Bank 1)
Complete diagnosis with drive cycle A or B as well.
P2103
Throttle Actuator Control Motor Circuit High
Complete diagnosis with drive cycle A or B as well.
DTC
Item
Condition
*P0181
Fuel Temperature Sensor “A” Circuit Range/Performance
—
DTC
Item
Condition
*P0461
Fuel Level Sensor “A” Circuit Range/Performance
—
EN(H4DOTC)(diag)-51
Drive Cycle
ENGINE (DIAGNOSTICS)
7. DRIVE CYCLE F
1) Make sure that the engine coolant temperature at engine starting is less than 30°C (86°F).
2) Start the engine, and warm it up until engine coolant temperature increases over 95°C (203°F).
3) Idle the engine for more than 10 minutes in the condition of step 2.
NOTE:
Do not disconnect the battery terminals while diagnosing. (Data will be cleared by disconnecting the battery
terminals.)
8. DRIVE CYCLE G
1) Disconnect the battery negative terminal, and reconnect after 10 seconds has passed.
2) Start the engine and warm up engine until coolant temperature is 80°C (176°F).
3) Turn OFF the engine and wait until the coolant temperature drop to 40°C (104°F) or less.
NOTE:
Do not let engine coolant temperature drop to 5°C (41°F) or less.
4) Start the engine and warm up engine until coolant temperature is 80°C (176°F).
5) Turn OFF the engine and wait until the coolant temperature drop to 40°C (104°F) or less.
NOTE:
Do not let engine coolant temperature drop to 5°C (41°F) or less.
6) Start and idle the engine.
9. DRIVE CYCLE H
1) Perform the Clear Memory Mode. <Ref. to EN(H4DOTC)(diag)-52, Clear Memory Mode.>
2) With the ignition switch ON, read the engine coolant temperature, intake air temperature and fuel temper-
ature. <Ref. to EN(H4DOTC)(diag)-35, READ CURRENT DATA FOR ENGINE (NORMAL MODE), OPER-
ATION, Subaru Select Monitor.>
3) If the values from step 2) satisfy the following two conditions, start the engine.
Condition:
|Engine coolant temperature — intake air temperature |
d
5°C (41°F)
|Engine coolant temperature — fuel temperature |
d
2°C (36°F)
NOTE:
• If the conditions are not satisfied, turn the ignition switch to OFF and wait until the parameters are satisfied.
• Start AT vehicles in the “P” range, and MT vehicles in the neutral position.
4) Idle the engine for 1 minute under the conditions in step 3).
DTC
Item
Condition
*P0111
Intake Air Temperature Sensor 1 Circuit Range/Performance
—
DTC
Item
Condition
*
P0410
Secondary Air Injection System
—
*
P0411
Secondary Air Injection System Incorrect Flow Detected
—
P0414
Secondary Air Injection System Switching Valve “A” Circuit Shorted
—
P0417
Secondary Air Injection System Switching Valve “B” Circuit Shorted
—
P1418
Secondary Air Injection System Control “A” Circuit Shorted
—
*
P2440
Secondary Air Injection System Switching Valve Stuck Open (Bank 1)
—
*
P2441
Secondary Air Injection System Switching Valve Stuck Closed (Bank 1)
—
*
P2442
Secondary Air Injection System Switching Valve Stuck Open (Bank2)
—
*
P2443
Secondary Air Injection System Switching Valve Stuck Closed (Bank2)
—
DTC
Item
Condition
*
P1602
Control Module Programming Error
—
EN(H4DOTC)(diag)-52
Clear Memory Mode
ENGINE (DIAGNOSTICS)
13.Clear Memory Mode
A: OPERATION
NOTE:
When Clear Memory Mode is performed in OBD
mode of Subaru Select Monitor, only DTCs are
cleared.
1. SUBARU SELECT MONITOR (NORMAL
MODE)
1) On the «Main Menu» display screen, select the
{Each System Check}.
2) On the «System Selection Menu» display
screen, select the {Engine Control System}.
3) Click the [OK] button after the information of en-
gine type has been displayed.
4) On the «Engine Diagnosis» display screen, se-
lect the {Clearing Memory}.
5) When the “Clear Memory?” is shown on the
screen, click the [Yes] button.
6) When “Done” and “Turn off the ignition switch.”
are shown on the display screen, turn the ignition
switch to OFF.
NOTE:
• Initial diagnosis of electronic throttle control is
performed after memory clearance. Wait for 10
seconds or more after turning the ignition switch to
ON, and then start the engine.
• For detailed operation procedures, refer to the
“PC application help for Subaru Select Monitor”.
2. SUBARU SELECT MONITOR (OBD MODE)
1) On the «Main Menu» display screen, select the
{Each System Check}.
2) On the «System Selection Menu» display
screen, select the {Engine Control System}.
3) Click the [OK] button after the information of en-
gine type has been displayed.
4) On the «Engine Diagnosis» display screen, se-
lect the {OBD System}.
5) On the «OBD Menu» display screen, select the
{Clear Diagnostic Code}.
6) When the “Clear Diagnostic Code?” is shown on
the screen, click the [Yes] button.
7) When “Done” and “Turn off the ignition switch.”
is shown on the display screen, turn the ignition
switch to OFF.
NOTE:
• Initial diagnosis of electronic throttle control is
performed after memory clearance. Wait for 10
seconds or more after turning the ignition switch to
ON, and then start the engine.
• For detailed operation procedures, refer to the
“PC application help for Subaru Select Monitor”.
3. GENERAL SCAN TOOL
For procedures clearing memory using the general
scan tool, refer to the general scan tool operation
manual.
NOTE:
Initial diagnosis of electronic throttle control is per-
formed after memory clearance. For this reason,
start the engine after 10 seconds or more have
elapsed since the ignition switch was turned to ON.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст