Subaru Legacy IV (2008 year). Service manual — part 1125
SR-14
Sunroof Switch
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
6. Sunroof Switch
A: REMOVAL
1) Disconnect the ground cable from the battery.
2) Remove the spot map light lens (A) and sunroof
switch mounting screws (B).
3) Disconnect the harness connector, and then re-
move the sunroof switch.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. SEDAN MODEL
Measure the sunroof switch resistance.
2. WAGON MODEL
Measure the sunroof switch resistance.
NOTE:
If the glass lid does not operate or is not supplied
with power, move the glass lid using the hexagon
wrench. <Ref. to SR-8, FORCED DRIVE, Glass
Lid.>
LI-00313
(A)
LI-00314
(B)
Switch position
Terminal No.
Standard
Connector
No.
Open
1 and 3
Less than 1
:
R128
Close
3 and 4
Less than 1
:
Tilt up
1 and 3
Less than 1
:
R187
Tilt down
3 and 4
Less than 1
:
Switch position
Terminal No.
Standard
Open
1 and 3
Less than 1
:
Close
3 and 4
Less than 1
:
R128
3
4
5
1
2
SR-00098
R187
3
4
5
1
2
SR-00041
R128
3
4
5
1
2
SR-15
Sunshade
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
7. Sunshade
A: REMOVAL
1. SEDAN MODEL
1) Remove the glass lid. <Ref. to SR-6, SEDAN
MODEL, REMOVAL, Glass Lid.>
2) Loosen the TORX
®
bolt to remove the front sun-
shade bracket.
3) Pull the sunshade until the rear sunshade brack-
et comes into the sight, then loosen the TORX
®
bolts to remove the sunshade.
2. WAGON MODEL
1) Remove the frame assembly.
2) Remove the shade stopper (A) of the sunshade.
3) Pull out the sunshade (A) from the sunroof
frame.
SR-00122
SR-00123
SR-00093
(A)
SR-00086
(A)
SR-16
Sunshade
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. CHECK FOR MOVING LOAD OF
SUNSHADE
1) Attach a spring scale to sunshade edge using a
cloth.
2) Pull the spring scale to measure moving load of
the sunshade.
Moving load of sunshade:
Standard
18.0
r
5.0 N (1.8
r
0.5 kgf, 13
r
3.7 lbf)
NOTE:
Moving load is larger at the beginning of pulling a
spring scale, so take a spring scale reading while
sunshade sliding smoothly.
3) If moving load exceeds specifications, check the
glass lid, sunshade and frame assembly for im-
proper installation.
SR-00087
EI-2
General Description
EXTERIOR/INTERIOR TRIM
1. General Description
A: COMPONENT
1. FRONT GRILLE
2. UNDER COVER
(1)
Front grille ASSY
(5)
Front grille ASSY (OUTBACK
model)
Tightening torque:N·m (kgf-m, ft-lb)
(2)
Front grille emblem
T: 4.5 (0.46, 3.32)
(3)
Front grille bracket
(6)
Front upper grille (OUTBACK
model)
(4)
Front grille clip
Tightening torque:N·m (kgf-m, ft-lb)
T: 17.5 (1.78, 12.9)
EI-01716
(2)
(5)
(4)
(3)
T
(4)
(2)
(1)
(6)
EI-00681
T
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст