Subaru Legacy IV (2008 year). Service manual — part 800
6MT-13
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
11.TRANSMISSION MOUNTING
(1)
Pitching stopper
(7)
Upper cushion rubber
Tightening torque:N·m (kgf-m, ft-lb)
(2)
Spacer
(8)
Center crossmember
T1: 7.5 (0.8, 5.5)
(3)
Lower cushion rubber
(9)
Rear plate
T2: 35 (3.6, 25.8)
(4)
Front plate
(10)
Front crossmember
T3: 50 (5.1, 36.9)
(5)
Transmission cushion rubber
(11)
Dynamic damper
T4: 58 (5.9, 42.8)
(6)
Rear crossmember
(12)
Upper cushion rubber
T5: 70 (7.1, 51.6)
T6: 75 (7.6, 55.3)
T7: 140 (14.3, 103.3)
MT-01555
(1)
T4
T6
T5
T5
T2
T7
T2
T3
(2)
(4)
(5)
(12)
(8)
(7)
(3)
(2)
(9)
(6)
(3)
(10)
T1
(11)
6MT-14
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
C: CAUTION
• Wear appropriate work clothing, including a cap,
protective goggles and protective shoes when per-
forming any work.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust and dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• When disassembling the case and other light al-
loy parts, disassemble by using a plastic hammer.
Do not pry apart with screwdrivers or other tools.
• Vehicle components are extremely hot after driv-
ing. Be wary of receiving burns from heated parts.
• Use SUBARU genuine transmission gear oil,
grease or the equivalent. Do not mix transmission
gear oil, grease etc. of different grades or manufac-
turers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or rigid racks at the specified
points.
• Apply transmission gear oil onto sliding or revolv-
ing surfaces before installation.
• Replace deformed or damaged snap rings with
new parts.
• Before installing O-rings or oil seals, apply suffi-
cient amount of transmission gear oil to avoid dam-
age and deformation.
• Be careful not to incorrectly install or fail to install
O-rings, snap rings and other parts.
• Before securing a part on a vise, place cushion-
ing materials such as wood blocks, aluminum
plates, or waste cloth between the part and the
vise.
• Avoid damaging the mating surface of the case.
• Before applying liquid gasket, completely re-
move the old liquid gasket.
6MT-15
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
D: PREPARATION TOOL
1. SPECIAL TOOL
ILLUSTRATION
TOOL NUMBER
TOOL NAME
REMARKS
398791700
REMOVER
Used for removing and installing the spring pin
(6 mm).
399527700
PULLER SET
Used for removing and installing the roller bear-
ing (Differential).
(1) BOLT (899521412)
(2) PULLER (399527702)
(3) HOLDER (399527703)
(4) ADAPTER (398497701)
(5) BOLT (899520107)
(6) NUT (021008000)
498515700
REMOVER
Used for removing the roller bearing of the drive
pinion shaft.
498247001
MAGNET BASE
• Used for measuring backlash between the
side gear, pinion, and hypoid gear.
• Used with the DIAL GAUGE (498247100).
ST-398791700
ST-399527700
(1)
(2)
(3)
(4)
(5)
(6)
ST-498515700
ST-498247001
6MT-16
General Description
MANUAL TRANSMISSION AND DIFFERENTIAL
498247100
DIAL GAUGE
• Used for measuring backlash between the
side gear, pinion, and hypoid gear.
• Used together with MAGNET BASE
(498247001).
498077000
REMOVER
Used for removing the differential taper roller
bearing.
899858600
REMOVER
Used for removing the roller bearing.
499757002
INSTALLER
Used for installing the bearing cone of the trans-
fer driven gear (extension core side).
18630AA010
WRENCH COMPL
RETAINER
• Used for removing and installing the differen-
tial side retainer RH.
• WRENCH ASSEMBLY (499787000) can also
be used.
ILLUSTRATION
TOOL NUMBER
TOOL NAME
REMARKS
ST-498247100
ST-498077000
ST-899858600
ST-499757002
ST18630AA010
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст