Subaru Legacy IV (2008 year). Service manual — part 619
GD(H6DO)-96
Diagnostic Trouble Code (DTC) Detecting Criteria
GENERAL DESCRIPTION
BV:DTC P0332 KNOCK SENSOR 2 CIRCUIT LOW (BANK 2)
1. OUTLINE OF DIAGNOSIS
NOTE:
For the detection standard, refer to DTC P0327. <Ref. to GD(H6DO)-94, DTC P0327 KNOCK SENSOR 1
CIRCUIT LOW (BANK 1 OR SINGLE SENSOR), Diagnostic Trouble Code (DTC) Detecting Criteria.>
BW:DTC P0333 KNOCK SENSOR 2 CIRCUIT HIGH (BANK 2)
1. OUTLINE OF DIAGNOSIS
NOTE:
For the detection standard, refer to DTC P0328. <Ref. to GD(H6DO)-95, DTC P0328 KNOCK SENSOR 1
CIRCUIT HIGH (BANK 1 OR SINGLE SENSOR), Diagnostic Trouble Code (DTC) Detecting Criteria.>
GD(H6DO)-97
Diagnostic Trouble Code (DTC) Detecting Criteria
GENERAL DESCRIPTION
BX:DTC P0335 CRANKSHAFT POSITION SENSOR “A” CIRCUIT
1. OUTLINE OF DIAGNOSIS
Detect the open or short circuit of the crankshaft position sensor.
Judge as NG when the crank signal is not input even though the starter was rotated.
2. COMPONENT DESCRIPTION
3. ENABLE CONDITION
4. GENERAL DRIVING CYCLE
Always perform the diagnosis continuously.
(A)
Camshaft signal (RH)
(B)
Camshaft signal (LH)
(C)
Crankshaft signal
(1)
Crankshaft position sensor
(2)
Crank sprocket
(3)
Crankshaft half-turn
Secondary Parameters
Enable Conditions
None
(A)
(C)
#6BTDC10 CA
#3BTDC10 CA
#2BTDC10 CA
#5BTDC10 CA
#4BTDC10 CA
10 CA
30 CA
30 CA
#1BTDC10 CA
#1BTDC10 CA
EN-03092
(B)
Number of camshaft signal - 3 is normal at two engine revolution in a range of 0 CA - 0 CA.
EN-02188
(1)
(2)
(3)
GD(H6DO)-98
Diagnostic Trouble Code (DTC) Detecting Criteria
GENERAL DESCRIPTION
5. DIAGNOSTIC METHOD
• Abnormality Judgement
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Time Needed for Diagnosis: 3000 ms
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
• Normality Judgement
Judge as OK and clear the NG if the continuous time while the following conditions are established is more
than the predetermined time.
Time Needed for Diagnosis: Less than 1 second
Judgement Value
Malfunction Criteria
Threshold Value
Starter switch
ON
Crankshaft position sensor signal
Not detected
Battery voltage
t 8 V
Judgement Value
Malfunction Criteria
Threshold Value
Crankshaft position sensor signal
Input exists
Battery voltage
t 8 V
GD(H6DO)-99
Diagnostic Trouble Code (DTC) Detecting Criteria
GENERAL DESCRIPTION
BY:DTC P0336 CRANKSHAFT POSITION SENSOR “A” CIRCUIT RANGE/
PERFORMANCE
1. OUTLINE OF DIAGNOSIS
Detect for faults in crankshaft position sensor output properties.
Judge as NG when there is a problem in the number of crankshaft signals for every revolution.
2. COMPONENT DESCRIPTION
3. ENABLE CONDITION
(A)
Camshaft signal (RH)
(B)
Camshaft signal (LH)
(C)
Crankshaft signal
(1)
Crankshaft position sensor
(2)
Crank sprocket
(3)
Crankshaft half-turn
Secondary Parameters
Enable Conditions
Battery voltage
t 8 V
Engine speed
< 3000 rpm
(A)
(C)
#6BTDC10 CA
#3BTDC10 CA
#2BTDC10 CA
#5BTDC10 CA
#4BTDC10 CA
10 CA
30 CA
30 CA
#1BTDC10 CA
#1BTDC10 CA
EN-03092
(B)
Number of camshaft signal - 3 is normal at two engine revolution in a range of 0 CA - 0 CA.
EN-02188
(1)
(2)
(3)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст