Subaru Legacy III (2000-2003 year). Service manual — part 196
EX(H4SOw/oOBD)-6
EXHAUST
GENERAL DESCRIPTION
3. WITHOUT CATALYTIC CONVERTER
EX-00100
( 1 )
( 2 )
( 3 )
( 4 )
( 5 )
( 6 )
( 7 )
( 8 )
( 9 )
(10)
(11)
(11)
(11)
(12)
(13)
(14)
(15)
(16)
(16)
T2
T4
T4
T4
T5
T5
T1
T6
T3
EX(H4SOw/oOBD)-7
EXHAUST
GENERAL DESCRIPTION
(1) Upper front exhaust pipe cover
(9) Self-locking nut
Tightening torque: N·m (kgf-m, ft-lb)
(2) Lower front exhaust pipe cover
(10) Gasket
T1: 8 (0.8, 5.8)
(3) Front exhaust pipe
(11) Cushion rubber
T2: 13 (1.3, 9.4)
(4) Upper center exhaust pipe cover
(12) Muffler
T3: 18 (1.8, 13.0)
(5) Lower center exhaust pipe cover
(13) Clamp
T4: 30 (3.1, 22.4)
(6) Center exhaust pipe
(14) Gasket
T5: 35 (3.6, 26.0)
(7) Spring
(15) Protector
T6: 48 (4.9, 35.4)
(8) Rear exhaust pipe
(16) Gasket
EX(H4SOw/oOBD)-8
EXHAUST
GENERAL DESCRIPTION
B: CAUTION
• Wear working clothing, including a cap, protec-
tive goggles, and protective shoes during opera-
tion.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust or dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly, and replacement.
• Be careful not to burn your hands, because each
part on the vehicle is hot after running.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or safety stands at the specified
points.
• Before disconnecting electrical connectors of
sensors or units, be sure to disconnect ground ca-
ble from battery.
EX(H4SOw/oOBD)-9
EXHAUST
FRONT EXHAUST PIPE
2. Front Exhaust Pipe
A: REMOVAL
1) Disconnect battery ground cable.
2) Disconnect front oxygen sensor connector.
(With catalytic converter)
3) Lift-up the vehicle.
4) Separate front and center exhaust pipe assem-
bly from rear exhaust pipe.
WARNING:
Be careful, exhaust pipe is hot.
5) Remove under cover. <Ref. to EI-13, REMOV-
AL, Front Under Cover.>
6) Remove nuts which hold front exhaust pipe onto
cylinder heads.
CAUTION:
Be careful not to pull down front and center ex-
haust pipe assembly.
7) Remove bolt which installs front and center ex-
haust pipe assembly to hanger bracket.
8) Remove front and center exhaust pipe assembly
from the vehicle.
CAUTION:
• Be careful not to let front and center exhaust
pipe assembly fall off when removing as it is
quite heavy.
• After removing front and center exhaust as-
sembly, do not apply excessive pulling force on
rear exhaust pipe.
9) Separate front exhaust pipe from center exhaust
pipe.
FU-00009
EX-00101
FU-00455
EX-00102
EX-00049
EX-00050
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст