Subaru Legacy III (2000-2003 year). Service manual — part 889
AB-12
AIRBAG SYSTEM
DRIVER'S AIRBAG MODULE
4. Driver's Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
1) Position front wheels straight ahead. (After mov-
ing a vehicle more than 5 m (16 ft) with front wheels
positioned straight ahead, make sure that the vehi-
cle moves straight ahead).
2) Turn ignition switch OFF.
3) Disconnect the ground cable from the battery,
and wait for at least 20 seconds before starting
work.
4) Using TORX
®
BIT T30, remove two TORX
®
bolts on side of steering wheel.
5) Disconnect airbag connector on back of airbag
module, and then remove airbag module.
6) Refer to “CAUTION” for handling of a removed
airbag module. <Ref. to AB-3, CAUTION,
GENERAL DESCRIPTION.>
B: INSTALLATION
1) Install in the reverse order of removal.
CAUTION:
Do not allow harness and connectors to inter-
fere or get tangled up with other parts.
C: INSPECTION
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
Check for the following, and replace damaged
parts with new parts.
• Airbag module, harness, connector, and mount-
ing bracket are damaged.
AB-00032
TORX BIT T30
R
AB-00033
AB-13
AIRBAG SYSTEM
PASSENGER'S AIRBAG MODULE
5. Passenger's Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
1) Turn ignition switch OFF.
2) Disconnect the ground cable from the battery,
and wait for at least 20 seconds before starting
work.
3) Remove glove box. <Ref. to EI-32, REMOVAL,
Glove Box.>
4) Disconnect airbag connector (A), and then de-
tach airbag connector from support beam bracket.
5) Remove three bolts, and then carefully remove
airbag module.
6) Refer to “CAUTION” for handling of a removed
airbag module. <Ref. to AB-3, CAUTION,
GENERAL DESCRIPTION.>
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Do not allow harness and connectors to inter-
fere or get tangled up with other parts.
C: INSPECTION
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
Check for the following, and replace damaged
parts with new parts.
• Airbag module, harness, connector, and mount-
ing bracket are damaged.
AB-00178
( A )
AB-14
AIRBAG SYSTEM
SIDE AIRBAG MODULE
6. Side Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
When replacing side airbag module: <Ref. to SE-9,
DISASSEMBLY, Front Seat.>
B: INSTALLATION
<Ref. to SE-8, INSTALLATION, Front Seat.>
C: INSPECTION
CAUTION:
Refer to “CAUTION” in General Description
before handling the airbag module. <Ref. to AB-
3, CAUTION, GENERAL DESCRIPTION.>
Check for the following, and replace damaged
parts with new parts.
• Front seat is deformed or damaged.
• Harness and/or connector is cracked, deformed
or open.
• Lead wire is exposed.
AB-15
AIRBAG SYSTEM
MAIN HARNESS
7. Main Harness
A: REMOVAL
1) Turn ignition switch OFF.
2) Disconnect the ground cable from the battery
and wait for at least 20 seconds before starting
work.
3) Remove instrument panel. <Ref. to EI-35, RE-
MOVAL, Instrument Panel Assembly.>
4) Disconnect connector from airbag control mod-
ule.
5) Disconnect front sub sensor connector (blue)
from airbag main harness.
6) Detach clips from steering support beam, and
remove main harness.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Check for the following, and replace damaged
parts with new parts.
• Harness and/or connector is damaged.
AB-00179
AB-00180
AB-00345
A
A
A - A
: ( 1 )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст