Subaru Legacy III (2000-2003 year). Service manual — part 335
EN(H6DO)-142
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
O: DTC P0117 — ENGINE COOLANT TEMPERATURE CIRCUIT LOW INPUT —
• DTC DETECTING CONDITION:
• Immediately at fault recognition
• TROUBLE SYMPTOM:
• Hard to start
• Erroneous idling
• Poor driving performance
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode <Ref. to EN(H6DO)-54, OP-
ERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H6DO)-47, OPERATION, Inspec-
tion Mode.>.
• WIRING DIAGRAM:
EN-00813
19
18
12
5
B135 ECM
2
1
E2
B21
E8
ENGINE
COOLANT
TEMPERATURE
SENSOR
E8
5
6
B83
B21
1 2
3 4
5
6 7
8
9 10
11 12
13
14 15
16
17 18
19 20
1 2
3
B83
B135
5 6
7 8
2
1
9
4
3
10
24
22
23
25
11 12 13 14 15
26 27 28
16 17 18 19
20 21
1 2 3 4
5 6 7 8 9 10
11 12
19 20
13 14 15 16 17 18
EN(H6DO)-143
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Step
Value
Yes
No
1
CHECK CURRENT DATA.
1) Start engine.
2) Read data of engine coolant temperature
sensor signal using Subaru Select Monitor
or OBD-II general scan tool.
Does the measured value exceed the spec-
ified value?
NOTE:
• Subaru Select Monitor
For detailed operation procedure, refer to the
“READ CURRENT DATA FOR ENGINE”.
<Ref. to EN(H6DO)-34, Subaru Select Moni-
tor.>
• OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Instruction Manual.
120
°
C (248
°
F)
Repair poor con-
tact.
NOTE:
In this case, repair
the following:
• Poor contact in
engine coolant
temperature sen-
sor
• Poor contact in
ECM
• Poor contact in
coupling connector
• Poor contact in
joint connector
2
CHECK HARNESS BETWEEN ENGINE
COOLANT TEMPERATURE SENSOR AND
ECM CONNECTOR.
1) Turn ignition switch to OFF.
2) Disconnect connector from engine coolant
temperature sensor.
3) Turn ignition switch to ON.
4) Read data of engine coolant temperature
sensor signal using Subaru Select Monitor
or OBD-II general scan tool.
Is the measured value less than the speci-
fied value?
NOTE:
• Subaru Select Monitor
For detailed operation procedure, refer to the
“READ CURRENT DATA FOR ENGINE”.
<Ref. to EN(H6DO)-34, Subaru Select Moni-
tor.>
• OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Instruction Manual.
−
40
°
C (
−
40
°
F)
Replace engine
coolant tempera-
ture sensor. <Ref.
to FU(H6DO)-29,
Engine Coolant
Temperature Sen-
sor.>
Repair ground
short circuit in har-
ness between
engine coolant
temperature sen-
sor and ECM con-
nector.
EN(H6DO)-144
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
P: DTC P0118 — ENGINE COOLANT TEMPERATURE CIRCUIT HIGH INPUT —
• DTC DETECTING CONDITION:
• Immediately at fault recognition
• TROUBLE SYMPTOM:
• Hard to start
• Erroneous idling
• Poor driving performance
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode <Ref. to EN(H6DO)-54, OP-
ERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H6DO)-47, OPERATION, Inspec-
tion Mode.>.
• WIRING DIAGRAM:
EN-00813
19
18
12
5
B135 ECM
2
1
E2
B21
E8
ENGINE
COOLANT
TEMPERATURE
SENSOR
E8
5
6
B83
B21
1 2
3 4
5
6 7
8
9 10
11 12
13
14 15
16
17 18
19 20
1 2
3
B83
B135
5 6
7 8
2
1
9
4
3
10
24
22
23
25
11 12 13 14 15
26 27 28
16 17 18 19
20 21
1 2 3 4
5 6 7 8 9 10
11 12
19 20
13 14 15 16 17 18
EN(H6DO)-145
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Step
Value
Yes
No
1
CHECK CURRENT DATA.
1) Start engine.
2) Read data of engine coolant temperature
sensor signal using Subaru Select Monitor
or OBD-II general scan tool.
Is the measured value less than the speci-
fied value?
NOTE:
• Subaru Select Monitor
For detailed operation procedure, refer to the
“READ CURRENT DATA FOR ENGINE”.
<Ref. to EN(H6DO)-34, Subaru Select Moni-
tor.>
• OBD-II general scan tool
For detailed operation procedures, refer to the
OBD-II General Scan Tool Instruction Manual.
−
40
°
C (
−
40
°
F)
Repair poor con-
tact.
NOTE:
In this case, repair
the following:
• Poor contact in
engine coolant
temperature sen-
sor
• Poor contact in
ECM
• Poor contact in
coupling connector
• Poor contact in
joint connector
2
CHECK HARNESS BETWEEN ENGINE
COOLANT TEMPERATURE SENSOR AND
ECM CONNECTOR.
1) Turn ignition switch to OFF.
2) Disconnect connector from engine coolant
temperature sensor.
3) Measure voltage between engine coolant
temperature sensor connector and engine
ground.
Connector & terminal
(E8) No. 1 (+) — Engine ground (
−−−−
):
Does the measured value exceed the spec-
ified value?
10 V
Repair battery
short circuit in har-
ness between
ECM and engine
coolant tempera-
ture sensor con-
nector.
3
CHECK HARNESS BETWEEN ENGINE
COOLANT TEMPERATURE SENSOR AND
ECM CONNECTOR.
1) Turn ignition switch to ON.
2) Measure voltage between engine coolant
temperature sensor connector and engine
ground.
Connector & terminal
(E8) No. 1 (+) — Engine ground (
−−−−
):
Does the measured value exceed the spec-
ified value?
10 V
Repair battery
short circuit in har-
ness between
ECM and engine
coolant tempera-
ture sensor con-
nector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст