Subaru Legacy III (2000-2003 year). Service manual — part 80
CO(H4SO)-28
COOLING
RADIATOR MAIN FAN AND FAN MOTOR
9. Radiator Main Fan and Fan
Motor
A: REMOVAL
1) Disconnect battery ground cable.
2) Lift-up the vehicle.
3) Remove under cover.
4) Disconnect connector of main fan motor.
5) Lower the vehicle.
6) Remove air intake duct.
7) Disconnect overflow hose.
8) Remove reservoir tank.
9) Remove radiator main fan motor assembly.
FU-00009
LU-00095
CO-00095
IN-00059
CO-00086
CO-00087
CO-00096
CO(H4SO)-29
COOLING
RADIATOR MAIN FAN AND FAN MOTOR
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
When the main fan motor assembly cannot be in-
stalled as is, loosen the sub fan motor assembly
securing bolts to install it.
・
Refer to “COMPONENT” for tightening torque.
<Ref. to CO(H4SO)-3, COMPONENT, General De-
scription.>
Tightening torque:
4.9 N·m (0.50 kgf-m, 3.6 ft-lb)
C: DISASSEMBLY
1) Remove clip which holds motor connector onto
shroud.
2) Remove nut which holds fan itself onto fan motor
and shroud assembly.
3) Remove bolts which install fan motor onto
shroud.
D: ASSEMBLY
Assemble in the reverse order of disassembly.
NOTE:
・
Refer to “COMPONENT” for tightening torque.
<Ref. to CO(H4SO)-3, COMPONENT, General De-
scription.>
E: INSPECTION
1) Connect battery positive (+) terminal to terminal
No. 2, and negative (
−
) terminal to terminal No. 1.
2) Make sure the main fan motor operates properly.
Replace it if it doesn't.
CO-00087
CO-00046
CO-00097
CO-00098
CO-00202
1 2
F17
To
CO(H4SO)-30
COOLING
RADIATOR SUB FAN AND FAN MOTOR
10.Radiator Sub Fan and Fan
Motor
A: REMOVAL
1) Disconnect battery ground cable.
2) Lift-up the vehicle.
3) Remove under cover.
4) Disconnect connector of sub fan motor.
5) Lower the vehicle.
6) Remove air intake duct.
7) Remove bolts which hold sub fan shroud to radi-
ator.
8) Remove radiator sub fan shroud through the un-
der side of vehicle.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
・
Refer to “COMPONENT” for tightening torque.
<Ref. to CO(H4SO)-3, COMPONENT, General De-
scription.>
C: DISASSEMBLY
1) Remove clip which holds motor harness onto
shroud.
2) Remove nut which holds fan itself onto fan motor
and shroud assembly.
FU-00009
LU-00095
CO-00100
IN-00059
CO-00101
CO-00046
CO-00102
CO(H4SO)-31
COOLING
RADIATOR SUB FAN AND FAN MOTOR
3) Remove bolts which install fan motor onto
shroud.
D: ASSEMBLY
Assemble in the reverse order of disassembly.
NOTE:
・
Refer to “COMPONENT” for tightening torque.
<Ref. to CO(H4SO)-3, COMPONENT, General De-
scription.>
E: INSPECTION
1) Connect battery positive (+) terminal to terminal
No. 2, and negative (
−
) terminal to terminal No. 1.
2) Make sure the sub-fan motor operates properly.
Replace it if it doesn't.
CO-00098
CO-00203
F16
1 2
To
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст