Subaru Legacy III (2000-2003 year). Service manual — part 774
VDC-132
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH SELECT MONITOR
8
CHECK OUTPUT SIGNAL FOR VDCCM.
1) Turn ignition switch to ON.
2) Measure voltage between data link connec-
tor and chassis ground.
Connector & terminal
(B40) No. 5 (
++++
) — Chassis ground (
−−−−
):
(B40) No. 4 (
++++
) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Repair harness
and connector
between each
control module
and data link con-
nector.
9
CHECK HARNESS/CONNECTOR BETWEEN
VDCCM AND DATA LINK CONNECTOR.
Measure resistance between VDCCM connec-
tor and data link connector.
Connector & terminal
(F87) No. 11 — (B40) No. 5:
(F87) No. 38 — (B40) No. 4:
Does the measured value exceed the specified
value?
0.5
Ω
Repair harness
and connector
between VDCCM
and data link con-
nector.
10
CHECK INSTALLATION OF VDCCM CON-
NECTOR.
Turn ignition switch to OFF.
Is VDCCM connector inserted into VDCCM
until the clamp locks onto it?
VDCCM connector is con-
nected and the clamp is
locked.
Insert VDCCM
connector into
VDCCM until the
clamp locks onto
it.
11
CHECK POWER SUPPLY CIRCUIT.
1) Turn ignition switch to ON (engine OFF).
2) Measure ignition power supply voltage
between VDCCM connector and chassis
ground.
Connector & terminal
(F87) No. 28 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
10 V
Repair open circuit
in harness
between VDCCM
and battery.
12
CHECK HARNESS CONNECTOR BETWEEN
VDCCM AND CHASSIS GROUND.
1) Turn ignition switch to OFF.
2) Disconnect connector from VDCCM and
transmission.
3) Measure resistance of harness between
VDCCM and chassis ground.
Connector & terminal
(F87) No. 1 — Chassis ground:
(F87) No. 55 — Chassis ground:
Is the measured value less than the speci-
fied value?
Does the measured value exceed the spec-
ified value?
1
Ω
Repair open circuit
in harness
between VDCCM
and inhibitor side
connector, and
poor contact in
coupling connec-
tor.
13
CHECK POOR CONTACT IN CONNECTORS.
Is there poor contact in control module power
supply, ground line and data link connector?
There is poor contact.
Repair connector.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
Step
Value
Yes
No
VDC-133
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH SELECT MONITOR
B: DTC 21 FRONT RIGHT ABS SENSOR CIRCUIT OPEN OR SHORTED BAT-
TERY
NOTE:
For diagnostic procedure, refer to DTC 27. <Ref. to VDC-134, DTC 27 REAR LEFT ABS SENSOR CIRCUIT
OPEN OR SHORTED BATTERY, Diagnostics Chart with Select Monitor.>
C: DTC 23 FRONT LEFT ABS SENSOR CIRCUIT OPEN OR SHORTED BAT-
TERY
NOTE:
For diagnostic procedure, refer to DTC 27. <Ref. to VDC-134, DTC 27 REAR LEFT ABS SENSOR CIRCUIT
OPEN OR SHORTED BATTERY, Diagnostics Chart with Select Monitor.>
D: DTC 25 REAR RIGHT ABS SENSOR CIRCUIT OPEN OR SHORTED BAT-
TERY
NOTE:
For diagnostic procedure, refer to DTC 27. <Ref. to VDC-134, DTC 27 REAR LEFT ABS SENSOR CIRCUIT
OPEN OR SHORTED BATTERY, Diagnostics Chart with Select Monitor.>
VDC-134
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH SELECT MONITOR
E: DTC 27 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORTED BATTERY
DIAGNOSIS:
• Faulty ABS sensor (Broken wire, input voltage too high)
• Faulty harness connector
TROUBLE SYMPTOM:
• ABS does not operate.
• VDC does not operate.
WIRING DIAGRAM:
VDC00174
F55
F88
B15
B6
2 1
R72
R73
F45
F2
1
2
2
1
7
6
2
1
4
1
3
F88
17
15
12
13
16
14
R
10
L
F45
B62
:
:
F2
B100
:
:
F55
R49
B15
R73
49
19
17
16
14
15
1
55
46
18
1
2
B6
2
1
R72
8
9
11
12
13
VDC CONTROL MODULE
FRONT ABS
SENSOR LH
FRONT ABS
SENSOR RH
LHD
RHD
REAR ABS
SENSOR LH
REAR ABS
SENSOR RH
F87
56 57
59 60
62 63
65
82 83
80
27
28
25
26
23
24
21
22
19
20
17
18
15
16
13
14
11
12
9
10
7
8
5
6
3
4
1
2
54
55
52
53
50
51
81
48
49
46
47
44
45
78
79
76
77
75
42
43
40
41
74
72
73
70
71
39
37
38
35
36
69
67
68
66
33
34
61
64
31
32
29
30
58
F87
: RHD MODEL
:LHD MODEL
R
R
R
L
L
L
1
3
4 5 6
2
1 2
3 4 5
6 7 8 9 10 11 12
1 2 3
4 5 6 7
8 9 10 11 12 13 14 15 16
3 4
1 2
8 9 10 11
12 13 14 15 16 17 18 19 20 21 22 23 24
5 6
7
VDC-135
VDC (DIAGNOSTICS)
DIAGNOSTICS CHART WITH SELECT MONITOR
Step
Value
Yes
No
1
CHECK OUTPUT OF ABS SENSOR USING
SELECT MONITOR.
1) Select “Current data display & Save” on the
select monitor.
2) Read the ABS sensor output corresponding
to the faulty system in the select monitor
data display mode.
Does the speed indicated on the display
change in response to the speedometer
reading during acceleration/deceleration
when the steering wheel is in the straight-
ahead position?
Change
2
CHECK INSTALLATION OF ABS SENSOR.
Are the ABS sensor installation bolts tightened
securely?
Tightening torque:
33
±±±±
10 N·m (3.3
±±±±
1.0 kgf-m, 24
±±±±
7 ft-lb)
Tightened securely.
Tighten ABS sen-
sor installation
bolts securely.
3
CHECK ABS SENSOR GAP.
Measure tone wheel-to-pole piece gap over
entire perimeter of the wheel.
Is the measured value within the specified
range?
Front wheel 0.3 - 0.8 mm
(0.012 - 0.031 in) and Rear
wheel 0.44 - 0.94 mm (0.0173 -
0.0370 in)
Adjust the gap.
NOTE:
Adjust the gap us-
ing spacers (Part
No. 26755AA000).
If spacers cannot
correct the gap, re-
place worn sensor
or worn tone
wheel.
4
CHECK TONE WHEEL RUNOUT.
Measure tone wheel runout.
Is the measured value less than the specified
value?
0.05 mm (0.0020 in)
Repair tone wheel.
Front <Ref. to
VDC-29, Front
Tone Wheel.>
Rear <Ref. to
VDC-30, Rear
Tone Wheel.>
5
CHECK POOR CONTACT IN CONNECTORS.
Turn ignition switch to OFF.
Is there poor contact in connectors between
VDCCM and ABS sensor?
There is poor contact.
Repair connector.
6
CHECK VDCCM.
1) Connect all connectors.
2) Erase the memory.
3) Perform inspection mode.
4) Read out the diagnostic trouble code.
Is the same diagnostic trouble code as in
the current diagnosis still being output?
Same pattern.
Replace VDCCM.
<Ref. to VDC-8,
VDC Control Mod-
ule (VDCCM).>
7
CHECK ANY OTHER DIAGNOSTIC TROU-
BLE CODES APPEARANCE.
Are other diagnostic trouble codes being out-
put?
Other DTC indicated.
Proceed with the
diagnosis corre-
sponding to the
diagnostic trouble
code.
A temporary poor
contact.
NOTE:
Check harness
and connectors
between VDCCM
and ABS sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст