Subaru Legacy III (2000-2003 year). Service manual — part 375
EN(H6DO)-302
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
CE:DTC P0865 — TCM COMMUNICATION CIRCUIT LOW —
• DTC DETECTING CONDITION:
• Two consecutive driving cycles with fault
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode <Ref. to EN(H6DO)-54, OP-
ERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H6DO)-47, OPERATION, Inspec-
tion Mode.>.
• WIRING DIAGRAM:
EN-01099
B56
B135
20
21
B135 ECM
TCM
B56
1 2
7
8
9
5 6
3 4
10 11 12
19 20 21
13
14 15
16
17
18
22
23
24
5 6
7 8
2
1
9
4
3
10
24
22
23
25
11 12 13 14 15
26 27 28
16 17 18 19
20 21
EN(H6DO)-303
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Step
Value
Yes
No
1
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
1) Turn ignition switch to ON.
2) Measure voltage between ECM and chas-
sis ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Is the measured value less than the speci-
fied value?
1 V
Even if MI lights
up, the circuit has
returned to a nor-
mal condition at
this time.
NOTE:
In this case, repair
the following:
• Poor contact in
ECM connector
• Poor contact in
TCM connector
2
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
1) Turn ignition switch to OFF.
2) Disconnect connector from ECM and TCM.
3) Measure resistance of harness between
ECM and chassis ground.
Connector & terminal
(B135) No. 20 — Chassis ground:
Is the measured value less than the speci-
fied value?
10
Ω
Repair ground
short circuit in har-
ness between
ECM and TCM
connector.
3
CHECK OUTPUT SIGNAL FOR ECM.
1) Connect connector to ECM.
2) Turn ignition switch to ON.
3) Measure voltage between ECM and chas-
sis ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Does the measured value exceed the spec-
ified value?
5 V
Repair poor con-
tact in ECM con-
nector.
4
CHECK TROUBLE CODE FOR AUTOMATIC
TRANSMISSION.
Read trouble code for automatic transmission.
<Ref. to AT-24, Read Diagnostic Trouble Code
(DTC).>
Does trouble code appear for automatic trans-
mission?
Trouble code for automatic
transmission is indicated.
Inspect trouble
code for auto-
matic transmis-
sion.
Replace TCM.
<Ref. to AT-76,
Transmission Con-
trol Module
(TCM).>
EN(H6DO)-304
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
CF:DTC P0866 — TCM COMMUNICATION CIRCUIT HIGH —
• DTC DETECTING CONDITION:
• Two consecutive driving cycles with fault
CAUTION:
After repair or replacement of faulty parts, conduct Clear Memory Mode <Ref. to EN(H6DO)-54, OP-
ERATION, Clear Memory Mode.> and Inspection Mode <Ref. to EN(H6DO)-47, OPERATION, Inspec-
tion Mode.>.
• WIRING DIAGRAM:
EN-01099
B56
B135
20
21
B135 ECM
TCM
B56
1 2
7
8
9
5 6
3 4
10 11 12
19 20 21
13
14 15
16
17
18
22
23
24
5 6
7 8
2
1
9
4
3
10
24
22
23
25
11 12 13 14 15
26 27 28
16 17 18 19
20 21
EN(H6DO)-305
ENGINE (DIAGNOSTICS)
DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC)
Step
Value
Yes
No
1
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
1) Turn ignition switch to ON.
2) Measure voltage between ECM and chas-
sis ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Does the measured value exceed the spec-
ified value?
10 V
Repair battery
short circuit in har-
ness between
ECM and TCM
connector.
2
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
Measure voltage between ECM connector and
chassis ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Does the measured value exceed the specified
value?
4 V
3
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
Measure voltage between ECM connector and
chassis ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Is the measured value less than the specified
value?
1 V
Repair poor con-
tact in ECM con-
nector.
4
CHECK OUTPUT SIGNAL FROM ECM.
Measure voltage between ECM and chassis
ground.
Connector & terminal
(B135) No. 20 (+) — Chassis ground (
−−−−
):
Does the measured value change within the
specified range?
1 V — 4 V
Even if MI lights
up, the circuit has
returned to a nor-
mal condition at
this time.
NOTE:
In this case, repair
the following:
• Poor contact in
ECM connector
• Poor contact in
TCM connector
Contact SUBARU
distributor service.
NOTE:
Inspection by DTM
is required, be-
cause probable
cause is deteriora-
tion of multiple
parts.
5
CHECK HARNESS BETWEEN ECM AND
TCM CONNECTOR.
Measure voltage between TCM and chassis
ground.
Connector & terminal
(B56) No. 21 (+) — Chassis ground (
−−−−
):
Does the measured value exceed the specified
value?
4 V
Repair open circuit
in harness
between ECM and
TCM connector.
6
CHECK POOR CONTACT.
Check poor contact in TCM connector.
Is there poor contact in TCM connector?
There is poor contact.
Repair poor con-
tact in TCM con-
nector.
Check TCM power
supply line and
grounding line.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст