Subaru Legacy III (2000-2003 year). Service manual — part 399
FU(H4DOSTC)-62
FUEL INJECTION (FUEL SYSTEMS)
FUEL SUB LEVEL SENSOR
24.Fuel Sub Level Sensor
A: REMOVAL
WARNING:
• Place “NO FIRE” signs near the working area.
• Be careful not to spill fuel on the floor.
1) Disconnect the ground cable from battery.
2) Lift-up the vehicle.
3) Remove the front side fuel tank cover.
4) Drain fuel from fuel tank. Set a container under
the vehicle, and then remove the drain plug from
fuel tank.
5) Tighten the fuel drain plug and install the protec-
tor RH (Front).
Tightening torque:
26 N·m (2.65 kgf-m, 19.2 ft-lb)
Tightening torque:
18 N·m (1.8 kgf-m, 13.0 ft-lb)
6) Remove the rear seat.
7) Remove the service hole cover.
8) Disconnect the connector from fuel sub level
sensor.
FU-00009
FU-00443
FU-00444
FU-00444
FU-00443
FU-00445
FU-00446
FU(H4DOSTC)-63
FUEL INJECTION (FUEL SYSTEMS)
FUEL SUB LEVEL SENSOR
9) Disconnect the fuel jet pump hose.
10) Remove the bolts which install fuel sub level
sensor on fuel tank.
11) Remove the fuel sub level sensor.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
4.4 N·m (0.45 kgf-m, 3.3 ft-lb)
FU-00447
FU-00448
FU-00448
FU(H4DOSTC)-64
FUEL INJECTION (FUEL SYSTEMS)
FUEL FILTER
25.Fuel Filter
A: REMOVAL
WARNING:
• Place “NO FIRE” signs near the working area.
• Be careful not to spill fuel on the floor.
NOTE:
The fuel filter is built in fuel pump assembly.
1) Release the fuel pressure. <Ref. to
FU(H4DOSTC)-44, RELEASING OF FUEL PRES-
SURE, OPERATION, Fuel.>
2) Remove the fuel pump assembly. <Ref. to
FU(H4DOSTC)-59, REMOVAL, Fuel Pump.>
3) Disconnect the ground cable from filter holder.
4) Remove the filter holder by turning it to the left
from the body pawls, and then take out the filter.
B: INSTALLATION
NOTE:
• If the fuel hoses are damaged at the connecting
portion, replace it with a new one.
• If the clamps are badly damaged, replace with
new ones.
• Replace the o-ring with new ones.
1) Set the O-ring on the filter holder, and then in-
stall by turning to the right.
2) Install the fuel pump assembly. <Ref. to
FU(H4DOSTC)-60, INSTALLATION, Fuel Pump.>
C: INSPECTION
1) Check the inside of fuel filter for dirt and water
sediment.
2) If it is clogged, or if replacement interval has
been reached, replace it.
FU-00682
FU-00683
FU-00683
FU(H4DOSTC)-65
FUEL INJECTION (FUEL SYSTEMS)
FUEL CUT VALVE
26.Fuel Cut Valve
A: REMOVAL
1) Remove the fuel tank. <Ref. to FU(H4DOSTC)-
47, REMOVAL, Fuel Tank.>
2) Move the clip, and then disconnect the evapora-
tion hose from fuel cut valve.
3) Remove the bolts which install fuel cut valve.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
4.4 N·m (0.45 kgf-m, 3.3 ft-lb)
FU-00684
FU-00685
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст