Subaru Legacy III (2000-2003 year). Service manual — part 531
AT-18
AUTOMATIC TRANSMISSION
GENERAL DESCRIPTION
C: CAUTION
• Wear working clothing, including a cap, protec-
tive goggles, and protective shoes during opera-
tion.
• Remove contamination including dirt and corro-
sion before removal, installation, and disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust or dirt.
• Until the oil pan is removed, do not place with the
oil pan side facing up to prevent foreign matter from
entering the valve body.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly and replacement.
• When disassembling the case and other light al-
loy parts, use a plastic hammer to force it apart. Do
not pry it apart with a screwdriver or other tool.
• Be careful not to burn your hands, because each
part on the vehicle is hot after running.
• Use Subaru genuine gear oil, grease etc. or the
equivalent. Do not mix gear oil, grease etc. with
that of another grade or from other manufacturers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or safety stands at the specified
points.
• Apply gear oil onto sliding or revolution surfaces
before installation.
• Replace deformed or otherwise damaged snap
rings with new ones.
• Before installing O-rings or oil seals, apply suffi-
cient amount of ATF fluid to avoid damage and de-
formation.
• Be careful not to incorrectly install or fail to install
O-rings, snap rings and other such parts.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or shop cloth between the part and the vise.
• Avoid damaging the mating surface of the case.
• Before applying sealant, completely remove the
old seal.
AT-19
AUTOMATIC TRANSMISSION
GENERAL DESCRIPTION
D: PREPARATION TOOL
1. SPECIAL TOOLS
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
498575400
OIL PRESSURE
GAUGE ASSY
Used for measuring oil pressure.
498897200
ADAPTER
Used oil pump housing when measuring reverse
clutch pressure and line pressure.
498897700
ADAPTER SET
Used for measuring transfer clutch pressure.
498545400
FILTER WRENCH
Used for removing and installing ATF filter.
ST-498575400
ST-498897200
ST-498897700
ST-498545400
AT-20
AUTOMATIC TRANSMISSION
GENERAL DESCRIPTION
498277200
STOPPER SET
Used for removing and installing automatic trans-
mission assembly to engine.
41099AA000
ENGINE SUP-
PORT ASSY
Used for supporting engine.
(1) ENGINE SUPPORT BRACKET (41099AA010)
(2) ENGINE SUPPORT (41099AA020)
499977400
CRANKSHAFT
PULLEY
WRENCH
• Used for rotating crankshaft.
• Used for 2.0 L model.
49977100
CRANKSHAFT
PULLEY
WRENCH
• Use for rotating crankshaft.
• Used for 2.5 L and 3.0 L models.
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-498277200
ST41099AA000
(2)
(1)
ST-499977400
ST-499977100
AT-21
AUTOMATIC TRANSMISSION
GENERAL DESCRIPTION
398527700
PULLER ASSY
• Used for removing extension case roller bear-
ing.
• Used for removing extension oil seal.
• Used for removing front differential side retainer
bearing outer race.
• Used for removing front differential side retainer
bearing outer ball race.
498057300
INSTALLER
Used for installing extension oil seal.
498077000
REMOVER
Used for removing differential taper roller bearing.
499247400
INSTALLER
• Used for installing transfer outer snap ring.
• Used with GUIDE (499257300).
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
ST-398527700
ST-498057300
ST-498077000
ST-499247400
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст