Subaru Legacy III (2000-2003 year). Service manual — part 1002
CC-28
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
DIAGNOSTICS CHART WITH TROUBLE CODE
B: DTC 22 VEHICLE SPEED SENSOR
DIAGNOSIS:
Disconnection or short circuit of vehicle speed sensor system.
TROUBLE SYMPTOM:
Cruise control cannot be set. (Cancelled immediately.)
WIRING DIAGRAM:
CRUISE
CONTROL
MODULE
B17
B94
GE
3
1
2
BATTERY
M/B NO. 5
C17
AT
19
6
B94
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
IGNITION
RELAY
VEHICLE SPEED
SENSOR (MT)
B56
C:
TRANSMISSION
CONTROL
MODULE
MT
B17
1 2 3
B56
C:
CC-00099
16
B22
E3
B22
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
1 2
7
8
9
5 6
3 4
10 11 12
19 20 21
13
14 15
16
17
18
22
23
24
CC-29
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
DIAGNOSTICS CHART WITH TROUBLE CODE
Step
Value
Yes
No
1
CHECK TRANSMISSION TYPE.
Is the transmission type MT?
Transmission type is MT.
2
CHECK HARNESS BETWEEN BATTERY
AND VEHICLE SPEED SENSOR.
1) Turn ignition switch to OFF.
2) Disconnect harness connector from vehicle
speed sensor.
3) Turn ignition switch to ON.
4) Measure voltage between vehicle speed
sensor harness connector terminal and
chassis ground.
Connector & terminal
(B17) No. 3 (+) — Chassis ground (
−−−−
):
Does the measured value exceed the spec-
ified value?
10 V
Check harness for
open or short
between ignition
relay and vehicle
speed sensor.
3
CHECK HARNESS BETWEEN CRUISE CON-
TROL MODULE AND VEHICLE SPEED SEN-
SOR.
1) Turn ignition switch to OFF.
2) Disconnect harness connector from cruise
control module.
3) Measure resistance between vehicle speed
sensor harness connector terminal and
cruise control module harness connector
terminal.
Connector & terminal
(B17) No. 1 — (B94) No. 19:
Is the measured value less than the speci-
fied value?
10
Ω
Repair harness.
4
CHECK HARNESS BETWEEN VEHICLE
SPEED SENSOR AND ENGINE GROUND.
Measure resistance between vehicle speed
sensor harness connector terminal and engine
ground.
Connector & terminal
(B17) No. 2 (+) — Engine ground (
−−−−
):
Is the measured value less than the specified
value?
10
Ω
Repair harness.
5
CHECK VEHICLE SPEED SENSOR.
1) Connect harness connector to vehicle
speed sensor.
2) Lift-up the vehicle and support with safety
stands.
3) Drive the vehicle at speed greater than 20
km/h (12 MPH).
Warning:
Be careful not to be caught up by the run-
ning wheels.
4) Measure voltage between cruise control
module harness connector terminal and
chassis ground.
Connector & terminal
(B94) No. 19 (+) — Chassis ground (
−−−−
):
Is the measured value same as the speci-
fied value?
0
←→
5 V
Replace cruise
control module.
<Ref. to CC-6,
Cruise Control
Module.>
Replace vehicle
speed sensor.
CC-30
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
DIAGNOSTICS CHART WITH TROUBLE CODE
6
CHECK HARNESS BETWEEN CRUISE CON-
TROL MODULE AND TRANSMISSION CON-
TROL MODULE.
1) Turn ignition switch to OFF.
2) Disconnect harness connector from trans-
mission control module and cruise control
module.
3) Measure resistance between cruise control
module harness connector terminal and
transmission control module harness con-
nector terminal.
Connector & terminal
(B94) No. 19 — (B56) No. 17:
Is the measured value less than the speci-
fied value?
10
Ω
?
Repair harness.
7
CHECK TRANSMISSION CONTROL MOD-
ULE.
1) Connect harness connector to transmission
control module.
2) Lift-up the vehicle and support with safety
stands.
3) Drive the vehicle faster than 10 km/h (6
MPH).
Warning:
Be careful not to be caught by the running
wheels.
4) Measure voltage between transmission
control module harness connector terminal
and chassis ground.
Connector & terminal
(B56) No. 17 (+) — Chassis ground (
−−−−
):
Is the measured value same as the speci-
fied value?
0
←→
5 V
Replace cruise
control module.
<Ref. to CC-6,
Cruise Control
Module.>
Replace transmis-
sion control mod-
ule. <Ref. to AT-
76, Transmission
Control Module
(TCM).>
Step
Value
Yes
No
CC-31
CRUISE CONTROL SYSTEM (DIAGNOSTICS)
DIAGNOSTICS CHART WITH TROUBLE CODE
C: DTC 28 WIRING HARNESS OPENED.
Step
Value
Yes
No
1
CHECK BATTERY.
Measure battery specific gravity of electrolyte.
Does the measured value exceed the specified
value?
1.250
Charge or replace
battery. Go to step
2.
2
CHECK FUSES, CONNECTORS AND HAR-
NESSES.
Check the condition of the main and other
fuses, and harnesses and connectors. Also
check for proper grounding.
Is there anything unusual about the appear-
ance of main fuse, fuse, harness, connector
and grounding?
Fuse, harness, connector and
grounding are OK.
End of inspection. Repair or replace
faulty parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст