Subaru Legacy III (2000-2003 year). Service manual — part 682
DS-6
DRIVE SHAFT SYSTEM
GENERAL DESCRIPTION
2. FRONT AXEL
(1) Baffle plate (SFJ)
(10) Boot (BJ)
(19) Hub bolt
(2) Spring pin
(11) BJ ASSY
(20) Hub
(3) Outer race (SFJ)
(12) Tone wheel
(21) Axle nut (Olive color)
(4) Snap ring
(13) Baffle plate
(5) Trunnion
(14) Oil seal (IN)
Tightening torque: N·m (kgf-m, ft-lb)
(6) Free ring
(15) Snap ring
T: 216 (22, 159)
(7) Circlip
(16) Bearing
(8) Boot band
(17) Housing
(9) Boot (SFJ)
(18) Oil seal (OUT)
DS-00138
( 3 )
( 6 )
( 8 )
( 8 )
( 8 )
( 9 )
( 7 )
( 5 )
( 4 )
( 2 )
( 1 )
(21)
(19)
(20)
(18)
(17)
(16)
(15)
(14)
(13)
(12)
(10)
(11)
T
DS-7
DRIVE SHAFT SYSTEM
GENERAL DESCRIPTION
3. REAR AXLE
(1) Baffle plate (DOJ)
(8) Boot band
(15) Hub
(2) Outer race (DOJ)
(9) Boot (DOJ)
(16) Axle nut (Olive color)
(3) Snap ring
(10) Boot (BJ)
(4) Inner race
(11) BJ ASSY
Tightening torque: N·m (kgf-m, ft-lb)
(5) Ball
(12) Tone wheel
T1: 66 (6.7, 48.5)
(6) Cage
(13) Hub unit bearing
T2: 186 (19, 137)
(7) Circlip
(14) Hub bolt
DS-00139
( 4 )
( 7 )
( 9 )
( 8 )
( 8 )
( 8 )
( 6 )
( 5 )
( 3 )
( 2 )
( 1 )
(16)
(15)
(13)
(14)
(11)
(12)
(10)
T1
T2
DS-8
DRIVE SHAFT SYSTEM
GENERAL DESCRIPTION
C: CAUTION
• Wear working clothing, including a cap, protec-
tive goggles, and protective shoes during opera-
tion.
• Remove contamination including dirt and corro-
sion before removal, installation or disassembly.
• Keep the disassembled parts in order and pro-
tect them from dust or dirt.
• Before removal, installation or disassembly, be
sure to clarify the failure. Avoid unnecessary re-
moval, installation, disassembly, and replacement.
• Be careful not to burn your hands, because each
part on the vehicle is hot after running.
• Use SUBARU genuine grease etc. or the equiv-
alent. Do not mix grease etc. with that of another
grade or from other manufacturers.
• Be sure to tighten fasteners including bolts and
nuts to the specified torque.
• Place shop jacks or safety stands at the specified
points.
• Apply grease onto sliding or revolution surfaces
before installation.
• Before installing O-rings or snap rings, apply suf-
ficient amount of grease to avoid damage and de-
formation.
• Before securing a part on a vise, place cushion-
ing material such as wood blocks, aluminum plate,
or shop cloth between the part and the vise.
DS-9
DRIVE SHAFT SYSTEM
GENERAL DESCRIPTION
D: MPREPARATION TOOL
1. SPECIAL TOOLS
ILLUSTRATION
TOOL NUMBER
DESCRIPTION
REMARKS
922431000
AXLE SHAFT
INSTALLER
• Used for installing axle shaft into housing.
• Used with ADAPTER (927390000).
925091000
BAND TIGHTEN-
ING TOOL
• Used for tightening boot band.
(A) Jig for band
(B) Ratchet wrench
926470000
AXLE SHAFT
PULLER
Used for removing axle shaft.
927060000
HUB REMOVER
• Used for removing front hub.
• Used with HUB STAND (927080000).
ST-922431000
ST-925091000
( A )
( B )
ST-926470000
ST-927060000
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст