Subaru BRZ (2012 year). Service manual — part 34
PM-65
Clutch System
PERIODIC MAINTENANCE SERVICES
13) Push the release lever until the operating cylinder push rod retracts. Make sure that the clutch fluid level
in the reservoir tank increases. If the clutch fluid level increases, the hydraulic clutch is properly adjusted. If
the clutch fluid level does not increase or the push rod does not retract, replace the master cylinder with a
new part.
14) Push the release lever until the operating cylinder push rod retracts. Check that the clutch fluid level in
the reservoir tank increases.
15) If the clutch fluid level increases, hydraulic clutch play is correct.
16) If the clutch fluid level does not increase or push rod does not retract, readjust the clutch pedal.
17) Check the clutch fluid level in the reservoir tank.
(A) Push rod
(B) Release lever
(C) Operating cylinder
(A) Push rod
(B) Release lever
(C) Operating cylinder
PM-00697
(A)
(B)
(C)
PM-00697
(A)
(B)
(C)
PM-66
Transmission Gear Oil
PERIODIC MAINTENANCE SERVICES
13.Transmission Gear Oil
A: INSPECTION
Check for leakage of gear oil from the transmission.
B: REPLACEMENT
CAUTION:
• Immediately after running the vehicle or after idling for a long time, the transmission gear oil will
be hot. Be careful not to receive burns.
• Be careful not to spill the transmission gear oil on exhaust pipe to prevent it from emitting smoke
or causing fires. If transmission gear oil is spilled on the exhaust pipe, wipe it off completely.
1) Lift up the vehicle.
2) Remove engine under cover No. 1.
3) Remove engine under cover No. 2.
4) Remove the transmission filler plug and gasket.
5) Remove the transmission drain plug and gasket, and drain the oil.
6) Install the transmission drain plug using a new gasket.
Tightening torque:
37 N·m (3.8 kgf-m, 27.3 ft-lb)
7) Pour transmission gear oil to the bottom end of filler plug.
NOTE:
Carefully refill transmission gear oil while checking the level. Excessive or insufficient oil must be avoided.
Recommended gear oil
Refer to “RM” section. <Ref. to RM-2, LUBRICANTS, RECOMMENDED MATERIALS, Recommend-
Transmission gear oil capacity
Refer to the “SPC” section. <Ref. to SPC-4, CAPACITY, BRZ.>
8) Tighten the filler plug using a new gasket.
Tightening torque:
37 N·m (3.8 kgf-m, 27.3 ft-lb)
9) Check that there is no oil leakage.
(A) Filler plug
(B) Drain plug
PM-00626
(A)
(B)
PM-67
Transmission Gear Oil
PERIODIC MAINTENANCE SERVICES
10) Install engine under cover No. 2.
11) Install engine under cover No. 1.
PM-68
Automatic Transmission Fluid
PERIODIC MAINTENANCE SERVICES
14.Automatic Transmission Fluid
A: INSPECTION
Check for leakage of ATF from transmission.
B: REPLACEMENT
1) Lift up the vehicle and maintain in a horizontal position.[*1]
2) Remove engine under cover No. 1.
3) Remove engine under cover No. 2.
4) Remove the drain plug and gasket, and drain the fluid.[*2]
5) Temporarily tighten the drain plug using a new gasket.[*3]
NOTE:
Replace the gasket and perform final tightening according procedures [*16].
6) Remove the refill plug (A) and O-ring.[*4]
7) Remove the overflow plug (B) using a socket hexagon wrench.[*5]
(A) Refill plug
(B) Overflow plug
(C) Refill hole
PM-00627
(C)
(A)
(B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст