Subaru Outback (2019 year). Instruction — part 29
(472,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
same or equivalent type of the
battery.
.
Batteries shall not be exposed to
excessive heat such as bright
sunlight, fire or the like.
NOTE
.
Replace only with the same or
equivalent type of battery recom-
mended by the manufacturer.
.
Dispose of used batteries according
to the local laws.
.
Mount the battery in the correct
orientation to prevent fluid leakage.
Be careful not to bend the terminals. It
may result in a malfunction.
.
It is recommended that the battery
should be replaced by a SUBARU deal-
er.
.
Use a new battery.
.
After replacing the battery, confirm
that the access key fob/transmitter
functions properly.
&
Replacing battery of access
key fob
CAUTION
.
When removing or fitting the
access key fob cover, make sure
that the plastic part does not
come off or become misaligned.
.
Before replacing the battery, re-
move any static electricity.
Battery: Button battery CR2032 or
equivalent
1)
Release button
2)
Emergency key
1. Take out the emergency key.
2. Wrap a flat-head screwdriver with vinyl
tape or a cloth, and insert it in the gap to
remove the cover.
3. Take out the battery using a flat-head
screwdriver with vinyl tape or a cloth.
Maintenance and service/Replacing battery
11-50
(473,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
4. Insert a new battery with its positive (+)
side facing upward as shown in the figure.
5. Attach the cover to the access key fob
by fitting the projections and recesses
together.
&
Replacing battery of trans-
mitter
CAUTION
Before replacing the battery, remove
any static electricity.
1. Open the key head using a flat-head
screwdriver.
2. Remove the transmitter case from the
key head.
3. Open the transmitter case by releasing
the hooks.
– CONTINUED –
Maintenance and service/Replacing battery
11-51
11
(474,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
1)
Negative (−) side facing up
4. Replace the old battery with a new
battery (Type CR1620 or equivalent) mak-
ing sure to install the new battery with the
negative (−) side facing up.
5. Put together the transmitter case by
fitting the hooks on the case.
6. Reinstall the transmitter case in the
key head.
7. Refit the removed half of the key head.
After the battery is replaced, the trans-
mitter must be synchronized with the
remote keyless entry system’s control
unit. Press either the “ ” or “
” button
six times to synchronize the unit.
Maintenance and service/Replacing battery
11-52
(477,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
Specifications. . . . . . . . . . . . . . 12-2
Dimensions. . . . . . . . . . . . . . ... 12-2
Engine . . . . . . . . . . . . . . . . .. 12-3
Fuel . . . . . . . . . . . . . . . . . .. 12-3
Engine oil . . . . . . . . . . . . . . . . 12-4
Front differential and rear differential gear oil. . 12-7
Fluids . . . . . . . . . . . . . . . . ... 12-8
Engine coolant. . . . . . . . . . . . . .. 12-8
Electrical system . . . . . . . . . . . . .. 12-9
Tires. . . . . . . . . . . . . . . . . . 12-9
Brake disc . . . . . . . . . . . . . . . 12-9
Fuses and circuits . . . . . . . . . . . .. 12-10
Fuse panel located in the passenger
compartment . . . . . . . . . . . . ... 12-10
Fuse panel located in the engine compartment ... 12-12
Bulb chart. . . . . . . . . . . . . . . 12-14
Safety precautions. . . . . . . . . . . .. 12-14
Bulb chart . . . . . . . . . . . . . . .. 12-15
Vehicle identification . . . . . . . . . . .. 12-18
Specifications
12
(478,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
Specifications
These specifications are subject to change without notice.
&
Dimensions
in (mm)
Item
Legacy
Outback
2.5 L
3.6 L
2.5 L
3.6 L
Drive system
AWD
Transmission type
CVT
Overall length
189.1 (4,802)
189.9 (4,824)
Overall width
72.4 (1,840)
72.4 (1,840)
Overall height
59.0 (1,500)
66.1 (1,680)*
2
65.2 (1,655)*
3
64.0 (1,625)*
4
Wheelbase
108.3 (2,750)
108.1 (2,745)
Tread
Front
62.2 (1,580)
61.8 (1,570)
Rear
62.8 (1,595)
62.2 (1,580)
Ground clearance*
1
5.9 (150)
8.7 (220)
*1: Measured with vehicle empty
*2: Models with high profile roof rails
*3: Models with low profile roof rails (U.S.-spec. models)
*4: Models with low profile roof rails (except U.S.-spec. models)
CVT: Continuously variable transmission
AWD: All-Wheel Drive
Specifications/Specifications
12-2
(479,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Engine
Engine model
FB25
(2.5 L, DOHC, non-turbo)
EZ36
(3.6 L, DOHC, non-turbo)
Engine type
Horizontally opposed, liquid cooled 4 cylinder,
4 stroke gasoline engine
Horizontally opposed, liquid cooled 6 cylinder,
4 stroke gasoline engine
Displacement cu-in (cc)
152 (2,498)
222 (3,630)
Bore 6 Stroke in (mm)
3.70 6 3.54 (94.0 6 90.0)
3.62 6 3.58 (92.0 6 91.0)
Compression ratio
10.3 : 1
10.5 : 1
Firing order
1 – 3 – 2 – 4
1 – 6 – 3 – 2 – 5 – 4
&
Fuel
Fuel requirement
Fuel tank capacity
Unleaded gasoline with 87 AKI (90 RON) or higher
18.5 US gal (70 liters, 15.4 Imp gal)
– CONTINUED –
Specifications/Specifications
12-3
12
(480,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Engine oil
For the checking, adding and replacing procedure or other details, refer to “Engine oil” F11-11.
NOTE
The procedure for changing the engine oil and oil filter should be performed by a properly-trained expert. It is recommended
that you have this service performed by your SUBARU dealer.
!
Approved engine oil
Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer.
If the approved engine oil is unavailable, use the alternative engine oil described on the next page.
!
Alternative engine oil
If the SUBARU approved oil is unavailable, the following alternative oil can be used.
NOTE
.
Each quantity indicated is only a guideline. The necessary quantity for replacement may differ slightly depending on the
temperature and other factors.
.
In choosing an oil, you want the proper quality and viscosity, as well as one that will enhance fuel economy. Oils of lower
viscosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the
engine. The following table lists the recommended viscosities and applicable temperatures.
.
When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity
as those recommended by SUBARU.
Specifications/Specifications
12-4
(481,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
!
2.5 L models
Oil grade
SAE viscosity No. and
applicable temperature
Engine oil capacity
API (American Petroleum Insti-
tute) classification SN with the
words “RESOURCE CONSER-
VING”
or
ILSAC (International Lubricant
Specification Advisory Commit-
tee) GF-5, which can be identi-
fied with the ILSAC certification
mark (Starburst mark)
0W-20 synthetic oil is the required oil
for optimum engine performance and
protection. Conventional oil may be
used if synthetic oil is unavailable.
*: If 0W-20 synthetic oil is not available,
5W-30 or 5W-40 conventional oil may
be used if you need to add oil. However,
you should change to 0W-20 synthetic
oil at the next oil change.
– Adding the oil from low level to
full level:
1.1 US qt (1.0 liter, 0.9 Imp qt)
– Changing the oil and oil filter:
5.1 US qt (4.8 liters, 4.2 Imp qt)
– CONTINUED –
Specifications/Specifications
12-5
12
(482,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
!
3.6 L models
Oil grade
SAE viscosity No. and
applicable temperature
Engine oil capacity
API (American Petroleum Insti-
tute) classification SN with the
words “RESOURCE CONSER-
VING”
or
ILSAC (International Lubricant
Specification Advisory Commit-
tee) GF-5, which can be identi-
fied with the ILSAC certification
mark (Starburst mark)
Your vehicle is designed to use 5W-30
conventional motor oil, however 5W-30
synthetic may be used for optimum
engine performance.
*: If 5W-30 synthetic oil is not available,
10W-30 or 10W-40 conventional oil
may be used if you need to add oil.
However, you should change to 5W-30
synthetic or conventional oil at the next
oil change.
– Adding the oil from L to F level:
1.1 US qt (1.0 liter, 0.9 Imp qt)
– Changing the oil and oil filter:
6.9 US qt (6.5 liters, 5.7 Imp qt)
Specifications/Specifications
12-6
(483,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Front differential and rear differential gear oil
Oil
Front differential gear oil
Rear differential gear oil
Oil grade
.
SUBARU Extra MT*
3
.
API classification GL-5 (75W-90)*
4
2.5 L models: SUBARU Extra MT*
3
or API classification GL-5 (75W-90*
4
)
3.6 L models: API classification GL-5 (75W-90*
3
or 90*
4
)
SAE viscosity No.
and applicable tem-
perature
—
.
75W-90*
.
90
*: Recommended
Oil capacity*
1
2.5 L models: 1.3 US qt (1.2 liters, 1.1 Imp qt)
3.6 L models: 1.5 US qt (1.4 liters, 1.2 Imp qt)
0.8 US qt (0.8 liters, 0.7 Imp qt)
Remarks*
2
“Front differential gear oil and rear differential gear oil”
“Front differential gear oil and rear differential gear oil” F11-19
*1: The indicated oil quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors. After refilling the gearbox with oil, the oil level should be checked.
*2: For more details about maintenance and service, refer to the indicated section.
*3: The vehicle is filled at the factory with this type of differential gear oil.
*4: You may use this type of differential gear oil. However, using this type of oil will detract from fuel efficiency.
– CONTINUED –
Specifications/Specifications
12-7
12
(484,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Fluids
Fluid
Fluid type*
1
Fluid capacity*
2
Remarks*
3
Continuously variable transmis-
sion fluid
Consult your SUBARU dealer.
2.5 L models:
· Legacy: 11.9 US qt (11.3 liters, 9.9 Imp qt)
· Outback: 12.4 US qt (11.7 liters, 10.3 Imp qt)
3.6 L models:
13.4 US qt (12.7 liters, 11.2 Imp qt)
“Continuously variable trans-
mission fluid” F11-19
Brake fluid
FMVSS No. 116, DOT 3 or DOT 4
brake fluid
–
*1: Use one of the indicated types of fluid.
*2: The indicated fluid quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors.
*3: For more details about maintenance and service, refer to the indicated section.
&
Engine coolant
Vehicle model
Coolant capacity
Coolant type
2.5 L models
8.2 US qt (7.8 liters, 6.9 Imp qt)
SUBARU Super Coolant
3.6 L models
7.4 US qt (7.0 liters, 6.2 Imp qt)
The indicated coolant quantity is only a guideline. The necessary quantity for replacement may differ slightly depending on the temperature and other
factors. For more details about maintenance and service, refer to “Cooling system” F11-14.
Specifications/Specifications
12-8
(485,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Electrical system
Battery type
75D23R
Alternator
2.5 L models: 12 V-150 A
3.6 L models: 12 V-130 A
Spark plugs
2.5 L models
SILZKAR7B11 (NGK)
3.6 L models
SILFR6C11 (NGK)
&
Tires
Item
Legacy
Outback
Tire size
225/55R17
97V
225/50R18
95H
225/65R17
102H
225/60R18
100H
Wheel size
17 6 7J
17 6 7 1/2J
18 6 7 1/2J
17 6 7J
18 6 7J
Pressure
Front
33 psi (230 kPa, 2.3 kgf/cm
2
)
35 psi (240 kPa, 2.4 kgf/cm
2
)
Rear
32 psi (220 kPa, 2.2 kgf/cm
2
)
33 psi (230 kPa, 2.3 kgf/cm
2
)
Temporary spare tire
Size
T155/70 D17 110M
T155/80 R17 101M
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2
)
Wheel nut tightening torque
88.5 lbf·ft (120 N·m, 12.2 kgf·m)*
1
*1: This torque is equivalent to applying approximately 88 to 110 lbf (40 to 50 kgf) at the end of the wheel nut wrench. If you have tightened the wheel nuts
by yourself, have the tightening torque checked at the nearest automotive service facility as soon as possible. For the wheel nut tightening procedure,
refer to “Changing a flat tire” F9-5.
&
Brake disc
If you need information on the usage limit value of brake discs and the method for measuring them, consult your SUBARU dealer.
Specifications/Specifications
12-9
12
(486,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
Fuses and circuits
&
Fuse panel located in the passenger compartment
Fuse
panel
Fuse
rating
Circuit
1
7.5 A
START1
2
20 A
12 V SOCKET
3
7.5 A
IG1-1
4
15 A
AUDIO NAVI
5
15 A
UNIT IG2-2
6
20 A
P/W R.LH
7
10 A
CIGAR
8
15 A
A/C IG
9
7.5 A
ACC
10
7.5 A
UNIT IG2-1
11
30 A
P/W MAIN1
12
7.5 A
START2
13
Empty
14
7.5 A
UNIT+B
15
7.5 A
METER IG
16
20 A
P/W R.RH
17
7.5 A
MIR
18
7.5 A
LAMP IG
19
7.5 A
IG1-2
20
10 A
SRS AIR BAG
21
20 A
P/W PASS1
22
15 A
SEAT HTR R
Specifications/Fuses and circuits
12-10
(487,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
Fuse
panel
Fuse
rating
Circuit
23
10 A
DRL
24
20 A
P/W MAIN2
25
Empty
26
10 A
BACK UP
27
15 A
WIPER DEICER
28
20 A
TRAIL R.FOG
29
20 A
P/W PASS2
30
Empty
31
7.5 A
SMT
32
15 A
SEAT HTR F
33
7.5 A
KEY SW
34
7.5 A
P/W ALL
35
20 A
SUN ROOF
36
Empty
37
7.5 A
STOP
38
7.5 A
EYE SIGHT
– CONTINUED –
Specifications/Fuses and circuits
12-11
12
(488,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
&
Fuse panel located in the engine compartment
A)
Main fuse
Fuse
panel
Fuse
rating
Circuit
1
7.5 A
HORN RH
2
7.5 A
HORN LH
3
10 A
ILLUMI
4
10 A
TAIL
5
15 A
H/L LO RH
6
15 A
H/L LO LH
7
10 A
H/L HI RH
8
10A
H/L HI LH
9
7.5 A
DCM
10
15 A
D/L
11
Empty
12
Empty*
1
7.5 A
ALT-S*
2
13
20 A
FUEL
14
15 A
HAZARD
15
30 A
IG2
16
7.5 A
PU B/UP
17
7.5 A
OBD
18
Empty
19
Empty
Specifications/Fuses and circuits
12-12
(489,1)
北米Model "A2550BE-A" EDITED: 2018/ 5/ 9
Fuse
panel
Fuse
rating
Circuit
20
20 A*
1
25 A*
2
O2 HTR
21
15 A
E/G2
22
15 A
ETC
23
15 A
E/G1
24
15 A
AVCS
25
15 A
INJ
26
7.5 A
CVT SSR
27
20 A
TCU
28
Empty
29
30 A
BACKUP
30
7.5 A
Empty*
2
ACTGS*
1
31
25 A
Empty*
2
SUB FAN*
1
32
25 A
Empty*
2
MAIN FAN*
1
33
30 A
ABS SOL
34
20 A
AUDIO
35
25 A
R.DEF
36
15 A
BLOWER
37
15 A
BLOWER
38
10 A
F.FOG RH
39
10 A
F.FOG LH
Fuse
panel
Fuse
rating
Circuit
40
Empty
41
15 A
STRG/H
42
15 A
R.WIPER
43
15 A
F.WASH
44
30 A
F.WIPER
45
Empty
*1: 2.5 L models
*2: 3.6 L models
Specifications/Fuses and circuits
12-13
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст