Subaru Crosstrek (2019 year). Manual — part 9
(135,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
!
Operating the window
.
With one-touch auto up and down
feature:
1)
Automatically close*
2)
Close
3)
Open
4)
Automatically open*
*: To stop the window halfway, operate the
switch to opposite side.
NOTE
Avoid the following.
.
After the driver’s window is fully
closed or fully opened, the switch is
continuously operated in the same
direction for a few seconds.
.
After the windows for three or more
seats are fully closed or fully opened,
each switch is continuously operated
in the same direction simultaneously
for a few seconds.
Either of the operations described
above may cause the power window
breaker to operate making it impossible
to open or close the window. Be sure to
initialize the power windows. If they are
not initialized, the one-touch auto up/
down function will not operate. Refer to
“Initialization of power window with
one-touch auto up/down function”
F2-30.
.
Without one-touch auto up and down
feature:
1)
Close
2)
Open
!
Anti-entrapment function (windows
with one-touch auto up/down func-
tion)
While closing the driver’s and front pas-
senger’s windows automatically, if the
window senses a substantial enough
object trapped between the window and
the window frame, it automatically moves
down slightly and stops.
If a foreign object is caught while the
driver’s window or passenger’s window is
opening automatically, the window will
stop.
CAUTION
.
Never attempt to test this func-
tion using fingers, hands or other
parts of your body.
.
The anti-entrapment function
may not operate properly if some
object gets trapped just before
the window fully closes.
NOTE
.
If a window detects an impact similar
to that caused by trapping an object (for
example, when the vehicle encounters
a deep pothole), the anti-entrapment
function may operate.
.
The window cannot be operated for a
– CONTINUED –
Keys and doors/Windows
2-29
2
(136,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
few seconds after the anti-entrapment
function operates.
!
Off delay function (windows with
one-touch auto up/down function)
The front windows can be operated for
approximately 45 seconds even after the
ignition switch is turned to the “ACC” or
“OFF” position. If a front door is opened
within 45 seconds, the off delay function is
canceled.
!
Locking the passengers’ windows
1)
Lock
2)
Unlock
When the lock switch is in the lock position,
the rear passenger’s window switches on
the driver side door and the passengers’
window switches cannot be operated.
&
Initialization of power window
with one-touch auto up/down
function
If the power window automatic function
(one-touch auto up and down function)
does not operate properly, operate each
window according to the following proce-
dure in order to initialize the power window
system.
1. Close the door.
2. Turn the ignition switch to the “ON”
position.
3. Open the window completely and then
press and hold down the power window
switch for approximately 1 second.
4. Close the window completely and then
pull and hold the power window switch for
approximately 1 second.
Rear gate
WARNING
.
To prevent dangerous exhaust
gas from entering the vehicle,
always keep the rear gate closed
while the engine is running.
.
Do not attempt to shut the rear
gate while holding the recessed
grip. Also avoid closing the rear
gate by pulling on the recessed
grip from inside the cargo space.
There is a danger of your hand
being caught and injured.
NOTE
If the rear gate cannot be unlocked due
to a discharged vehicle battery, a mal-
function in the door locking/unlocking
system or other causes, you can unlock
it by manually operating the rear gate
lock release lever.
For the procedure, refer to “Rear gate –
if the rear gate cannot be opened” F9-
19.
Keys and doors/Rear gate
2-30
(137,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
&
Lock/unlock
The rear gate can be locked and unlocked
using any of the following systems.
.
Power door locking switch: Refer to
“How to operate the power door locking
switches” F2-23.
.
Keyless access with the push-button
start system (if equipped): Refer to “Key-
less access with push-button start system”
F2-2.
.
Remote keyless entry system: Refer to
“Remote keyless entry system” F2-17.
&
Open/close
1)
The rear gate opener button
To open:
First unlock the rear gate lock then push
the rear gate opener button.
To close:
Lower the rear gate slowly and push down
firmly until the latch engages.
The rear gate can be lowered easily if you
pull it down holding the recessed grip.
CAUTION
.
Do not jam a plastic bag in or
place cellophane tape on the rear
gate stays or scratch the stays
while loading or unloading cargo.
That could cause leakage of gas
from the stays, which may result
in their inability to hold the rear
gate open.
– CONTINUED –
Keys and doors/Rear gate
2-31
2
(138,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
.
Be careful not to hit your head or
face on the rear gate when open-
ing or closing the rear gate and
when loading or unloading cargo.
Moonroof (if equipped)
WARNING
Never let anyone’s hands, arms,
head or any objects protrude from
the moonroof. A person could be
seriously injured if any of the follow-
ing conditions occur.
.
The vehicle stops suddenly.
.
The vehicle turns sharply.
.
The vehicle is involved in an
accident.
.
Body parts protruding from the
vehicle are struck by outside
objects.
To avoid serious personal injury
caused by entrapment, always con-
form to the following instructions
without exception.
.
Before closing the moonroof,
make sure that no one’s hands,
arms, head or other objects will
be accidentally caught in the
moonroof.
.
Always carry the key when you
leave the vehicle for safety rea-
sons and never allow an unat-
tended child to remain in the
vehicle. Failure to follow this
procedure could result in injury
to a child operating the moon-
roof.
.
Never try to check the anti-en-
trapment function by deliberately
placing part of your body in the
moonroof.
CAUTION
.
Do not sit on the edge of the open
moonroof.
.
Do not operate the moonroof if
falling snow or extremely cold
conditions have caused it to
freeze shut.
.
The anti-entrapment function
does not operate when the moon-
roof is being tilted down. Be sure
to confirm that it is safe to do so
before tilting the moonroof down.
.
If the moonroof does not close,
have the system checked by a
SUBARU dealer.
The moonroof has both tilting and sliding
functions.
The moonroof operates only when the
ignition switch is in the “ON” position.
Keys and doors/Moonroof
2-32
(139,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
&
Moonroof switches
!
Tilting moonroof
1)
Up
2)
Down
To raise the moonroof, press and hold the
switch in the up side and release. To lower
the moonroof, press and hold the switch in
the down side.
NOTE
Release the switch after the moonroof
has been raised or has been lowered
completely. Pressing the switch con-
tinuously may cause damage to the
moonroof.
!
Sliding moonroof
1)
Open
2)
Close
To open or close the moonroof using the
automatic function, press and hold the
switch toward the open/close side and
release.
To stop the moonroof halfway, press a
switch on the moonroof switch.
NOTE
.
After washing the vehicle or after it
rains, wipe away water on the roof prior
to opening the moonroof to prevent
drops of water from falling into the
passenger compartment.
.
For the sake of safety, it is recom-
mended that you avoid driving with the
moonroof fully opened.
!
Anti-entrapment function
When the moonroof senses a substantial
enough object trapped between its glass
and the vehicle’s roof during closure, it
automatically moves back to the fully open
position and stops there. The anti-entrap-
ment function may also be activated by a
strong shock on the moonroof even when
there is nothing trapped.
CAUTION
Never attempt to test this function
using fingers, hands or other parts
of your body.
– CONTINUED –
Keys and doors/Moonroof
2-33
2
(140,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
&
Sunshade
The sunshade can be slid forward or
backward by hand while the moonroof is
closed.
If the moonroof is opened, the sunshade
also moves back.
Keys and doors/Moonroof
2-34
(143,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
Ignition switch (models without “keyless
access with push-button start system”) . . . 3-4
Key positions. . . . . . . . . . . . . . . 3-4
Key reminder chime . . . . . . . . . . . ... 3-5
Ignition switch light (if equipped) . . . . . . ... 3-5
Push-button ignition switch (models with
“keyless access with push-button start
system”) . . . . . . . . . . . . . . . ... 3-6
Safety precautions . . . . . . . . . . . . . 3-6
Operating range for push-button start system . . 3-6
Switching power status . . . . . . . . . . .. 3-7
When access key fob does not operate properly . 3-8
Hazard warning flasher . . . . . . . . . . .. 3-8
Meters and gauges . . . . . . . . . . . . . 3-8
Speedometer . . . . . . . . . . . . . . . 3-8
Tachometer . . . . . . . . . . . . . . . 3-8
Odometer. . . . . . . . . . . . . . . ... 3-9
Double trip meter . . . . . . . . . . . . ... 3-9
Fuel gauge. . . . . . . . . . . . . . . 3-10
ECO gauge (if equipped) . . . . . . . . . ... 3-10
Combination meter settings . . . . . . . . .. 3-11
Illumination brightness control. . . . . . . 3-12
Auto dimmer cancel function (if equipped) . . . 3-12
Warning and indicator . . . . . . . . . . .. 3-12
Initial illumination for system check . . . . . .. 3-12
Seatbelt warning light and chime . . . . . . .. 3-13
SRS airbag system warning light. . . . . . ... 3-15
Front passenger’s frontal airbag ON and OFF
indicators . . . . . . . . . . . . . . ... 3-15
CHECK ENGINE warning light/Malfunction
indicator light . . . . . . . . . . . . . 3-15
Coolant temperature low indicator light/Coolant
temperature high warning light . . . . . . .. 3-16
Charge warning light . . . . . . . . . . . 3-17
Oil pressure warning light. . . . . . . . . . 3-17
Engine low oil level warning light. . . . . . .. 3-18
Windshield washer fluid warning light. . . . ... 3-18
AT OIL TEMP warning light (CVT models). . . .. 3-18
Low tire pressure warning light (U.S.-spec.
models) . . . . . . . . . . . . . . . . 3-18
ABS warning light. . . . . . . . . . . . . 3-20
Brake system warning light (red) . . . . . . .. 3-21
Low fuel warning light . . . . . . . . . . .. 3-22
Hill start assist warning light/Hill start assist
OFF indicator light. . . . . . . . . . . . 3-22
Door open warning light . . . . . . . . . ... 3-22
All-Wheel Drive warning light (CVT models) . . .. 3-22
Power steering warning light . . . . . . . . 3-23
Vehicle Dynamics Control warning light/Vehicle
Dynamics Control operation indicator light . . 3-23
Vehicle Dynamics Control OFF indicator light . ... 3-24
Warning chimes and warning indicator of the
keyless access with push-button start system
(if equipped) . . . . . . . . . . . . . .. 3-25
Security indicator light. . . . . . . . . . .. 3-29
Select lever/gear position indicator
(CVT models). . . . . . . . . . . . . . 3-30
Turn signal indicator lights . . . . . . . . ... 3-30
High beam indicator light. . . . . . . . . .. 3-30
High beam assist indicator light (if equipped) . ... 3-30
Instruments and controls
3
(144,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
Cruise control indicator light (if equipped). . . . 3-30
Cruise control set indicator light (if equipped) . ... 3-31
Automatic headlight beam leveler warning light
(models with LED headlights). . . . . . . .. 3-31
LED headlight warning light (models with LED
headlights). . . . . . . . . . . . . . .. 3-31
Steering Responsive Headlight warning light/
Steering Responsive Headlight OFF indicator
light (if equipped). . . . . . . . . . . . 3-31
Front fog light indicator light (if equipped) . . . 3-31
Headlight indicator light (if equipped). . . . . 3-31
Steering responsive fog lights warning indicator/
Steering responsive fog lights OFF indicator
(if equipped) . . . . . . . . . . . . . ... 3-31
X-MODE indicator (if equipped) . . . . . . . . 3-32
Hill descent control indicator (if equipped) . . . 3-32
BSD/RCTA warning indicator (if equipped). . . . 3-32
BSD/RCTA OFF indicator (if equipped) . . . . .. 3-32
RAB warning indicator (if equipped) . . . . . .. 3-32
RAB OFF indicator light (if equipped) . . . . . 3-32
Icy road surface warning indicator (if equipped) . 3-32
Combination meter display (color LCD)
(if equipped) . . . . . . . . . . . . . ... 3-33
Basic operation. . . . . . . . . . . . . . 3-34
Welcome screen (opening animation) and
Good-bye screen (ending animation) . . . . ... 3-34
Warning screen. . . . . . . . . . . . . . 3-35
Telltale screen. . . . . . . . . . . . . ... 3-35
Basic screens . . . . . . . . . . . . . ... 3-36
Menu screens . . . . . . . . . . . . . ... 3-38
Multi-function display (black and white). . . . 3-40
Driving information display . . . . . . . . ... 3-40
Outside temperature indicator. . . . . . . ... 3-44
X-MODE indicator (if equipped) . . . . . . . . 3-44
Clock. . . . . . . . . . . . . . . . . 3-44
Multi-function display (color LCD)
(if equipped) . . . . . . . . . . . . . ... 3-45
Features . . . . . . . . . . . . . . . ... 3-45
Welcome screen . . . . . . . . . . . . ... 3-45
Self-check screen . . . . . . . . . . . . . 3-46
Interruption screen . . . . . . . . . . . ... 3-46
Basic operation . . . . . . . . . . . . . 3-47
Basic screens. . . . . . . . . . . . . ... 3-47
Setting screen . . . . . . . . . . . . . .. 3-54
How to get the source code using the open
source. . . . . . . . . . . . . . . ... 3-59
Clock. . . . . . . . . . . . . . . . . .. 3-60
Setting the clock manually. . . . . . . . . 3-60
Setting the clock automatically . . . . . . . . 3-63
Regulatory information . . . . . . . . . . . 3-63
Light control switch . . . . . . . . . . . . 3-63
Precautions and tips. . . . . . . . . . . . 3-63
Headlights . . . . . . . . . . . . . . . 3-64
High/low beam change (dimmer) . . . . . . ... 3-65
Headlight flasher . . . . . . . . . . . . .. 3-66
High beam assist function (if equipped) . . . . 3-66
Daytime running light system . . . . . . . ... 3-69
Steering Responsive Headlight (SRH)
(if equipped) . . . . . . . . . . . . . ... 3-69
Instruments and controls
(145,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
Headlight beam leveler (models with LED
headlights). . . . . . . . . . . . . . .. 3-70
Fog light switch (if equipped) . . . . . . . .. 3-71
Steering responsive fog lights system
(if equipped) . . . . . . . . . . . . . ... 3-71
Turn signal lever . . . . . . . . . . . . ... 3-72
One-touch lane changer . . . . . . . . . . 3-73
Wiper and washer . . . . . . . . . . . . . 3-73
Windshield wiper and washer switches . . . . . 3-74
Rear window wiper and washer switch . . . . .. 3-76
Mirrors . . . . . . . . . . . . . . . . ... 3-77
Inside mirror. . . . . . . . . . . . . . . 3-77
Auto-dimming mirror/compass (if equipped). . .. 3-77
Auto-dimming mirror/compass with HomeLink
®
(if equipped) . . . . . . . . . . . . . .. 3-78
Outside mirrors . . . . . . . . . . . . . 3-85
Defogger and deicer (if equipped) . . . . . .. 3-86
Tilt/telescopic steering wheel . . . . . . . .. 3-87
Heated Steering Wheel system (if equipped) . . . 3-88
Horn . . . . . . . . . . . . . . . . . ... 3-89
Instruments and controls
(146,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
Ignition switch (models with-
out “keyless access with
push-button start system”)
WARNING
.
Never turn the ignition switch to
the “LOCK” position while the
vehicle is being driven or towed
because that will lock the steer-
ing wheel, preventing steering
control. And when the engine is
turned off, it takes a much greater
effort than usual to steer.
.
Before leaving the vehicle, al-
ways remove the key from the
ignition switch for safety and
never allow an unattended child
to remain in the vehicle. Failure to
follow this procedure could re-
sult in injury to a child or others.
Children could operate the power
windows, the moonroof or other
controls or even make the vehicle
move.
CAUTION
Do not attach a large key holder or
key case to either key. If it banged
against your knees or hands while
you are driving, it could turn the
ignition switch from the “ON” posi-
tion to the “ACC” or “LOCK” posi-
tion, thereby stopping the engine.
Also, if the key is attached to a key
holder or to a large bunch of other
keys, centrifugal force may act on it
as the vehicle moves, resulting in
unwanted turning of the ignition
switch.
The ignition switch has four positions:
LOCK, ACC, ON and START.
NOTE
.
Keep the ignition switch in the
“LOCK” position when the engine is
not running.
.
Using electrical accessories for a
long time with the ignition switch in the
“ON” or “ACC” position can cause the
battery to go dead.
.
If the ignition switch will not move
from the “LOCK” position to the “ACC”
position, turn the steering wheel
slightly to the left and right as you turn
the ignition switch.
&
Key positions
Position
Description
LOCK
The key can only be inserted
or removed in this position.
The ignition switch will lock
the steering wheel when you
remove the key.
ACC
In this position the electrical
accessories (audio, acces-
sory power outlet, etc.) can be
used.
ON
This is the normal operating
position after starting the en-
gine.
START
The engine is started in this
position.
Instruments and controls/Ignition switch (models without “keyless access with push-button start system”)
3-4
(147,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
CAUTION
Do not turn the ignition switch to the
“START” position while the engine
is running.
NOTE
.
To turn the key from the “ACC” to
“LOCK” position, the select lever must
be in the “P” position (CVT models) and
the key must be pushed in and turned.
.
If your registered key fails to start
the engine, pull out the key once (the
security indicator light will blink), and
then insert the key again and turn it to
the “START” position again to restart
the engine.
.
The engine may not start in the
following cases:
– The key grip is touching another
key or a metallic key holder.
– The key is near another key that
contains an immobilizer transpon-
der.
– The key is near or touching
another transmitter.
&
Key reminder chime
The reminder chime sounds when the
driver’s door is opened and the ignition
switch is in the “LOCK” or “ACC” position.
The chime stops under the following
conditions.
.
when the ignition switch is turned to the
“ON” position
.
when the key is removed from the
ignition switch
.
when the driver’s door is closed
&
Ignition switch light (if
equipped)
For easy access to the ignition switch in
the dark, the ignition switch light illumi-
nates when the driver’s door is opened or
when the driver’s door is unlocked using
the remote keyless entry transmitter.
The light remains illuminated for several
tens of seconds and then gradually turns
off under the following conditions.
.
when the driver’s door is closed
.
when the doors are unlocked using the
remote keyless entry transmitter
– CONTINUED –
Instruments and controls/Ignition switch (models without “keyless access with push-button start system”)
3-5
3
(148,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
The light turns off immediately under the
following conditions.
.
when the ignition switch is turned to the
“ON” position
.
when all doors and the rear gate are
locked using the remote keyless entry
transmitter
Push-button ignition switch
(models with “keyless access
with push-button start sys-
tem”)
&
Safety precautions
Refer to “Safety precautions” F2-3.
&
Operating range for push-
button start system
1)
Antenna
2)
Operating range
NOTE
.
If the access key fob is not detected
within the operating range of the anten-
nas inside the vehicle, the push-button
ignition switch and the engine start
cannot be operated.
.
Even when the access key fob is
outside the vehicle, if it is placed too
close to the glass, it may be possible to
switch the power or to start the engine.
.
Do not leave the access key fob in
the following places. It may become
impossible to operate the push-button
ignition switch and the engine start. It
may also cause a false warning to issue
although no malfunction actually oc-
curs, or not to issue a warning when
any malfunction occurs.
– On the instrument panel
– On the floor
– Inside the glove box
– Inside the door trim pocket
– On the rear seat
– In the cargo area
.
When operating the push-button
ignition switch or starting the engine,
if the access key fob battery is dis-
charged, perform the procedure de-
scribed in “Access key fob – if access
key fob does not operate properly” F9-
17. In such a case, replace the battery
immediately. Refer to “Replacing bat-
tery of access key fob” F11-44.
Instruments and controls/Push-button ignition switch (models with “keyless access with push-button start system”)
3-6
(149,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
&
Switching power status
1)
Operation indicator
2)
Push-button ignition switch
The power is switched every time the
push-button ignition switch is pressed.
1. Carry the access key fob, and sit in the
driver’s seat.
2. Shift the select lever (CVT models)/the
shift lever (MT models) into the “P”/“N”
position.
3. Press the push-button ignition switch
without depressing the brake pedal. Every
time the button is pressed, the power is
switched in the sequence of “OFF”, “ACC”,
“ON” and “OFF”. When the engine is
stopped and the push-button ignition
switch is in “ACC” or “ON”, the operation
indicator on the push-button ignition switch
illuminates in orange.
Power
status
Indicator color
Operation
OFF
Turned off
Power is turned
off.
ACC
Orange
The following
systems can be
used:
audio and ac-
cessory power
outlet.
ON
Orange
(while engine is
stopped)
All electrical
systems can be
used.
Turned off
(while engine is
running)
CAUTION
.
When the push-button ignition
switch is left in “ON” (while the
engine is not running) or “ACC”
for a long time, it may result in
vehicle battery discharge.
.
Do not spill drinks or other liquids
on the push-button ignition
switch. It may cause a malfunc-
tion.
.
Do not touch the push-button
ignition switch with a hand soiled
with oil or other contaminants. It
may cause a malfunction.
.
If the push-button ignition switch
does not operate smoothly, stop
the operation. Contact a SUBARU
dealer immediately.
.
If the push-button ignition switch
does not illuminate even when
the instrument panel illumination
is turned on, have the vehicle
inspected at a SUBARU dealer.
.
If the vehicle was left in the hot
sun for a long time, the surface of
the push-button ignition switch
may get hot. Be careful not to
burn yourself.
NOTE
.
When operating the push-button
ignition switch, firmly press it all the
way.
.
If the push-button ignition switch is
pressed quickly, the power may not
turn on or off.
– CONTINUED –
Instruments and controls/Push-button ignition switch (models with “keyless access with push-button start system”)
3-7
3
(150,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
.
If the indicator light on the push-
button ignition switch flashes in green
when the push-button ignition switch is
pressed, steering is locked. When this
occurs, press the push-button ignition
switch while turning the steering wheel
left and right.
!
Battery drainage prevention func-
tion
When the push-button ignition switch is left
in the “ACC” or “ON” position for approxi-
mately 1 hour, the push-button ignition
switch will be automatically switched to
“OFF” to prevent the battery from going
dead.
&
When access key fob does
not operate properly
Refer to “Access key fob – if access key
fob does not operate properly” F9-17.
Hazard warning flasher
The hazard warning flasher is used to warn
other drivers when you have to park your
vehicle under emergency conditions. The
hazard warning flasher works regardless
of the position of the ignition switch.
To turn on the hazard warning flasher,
push the hazard warning button on the
instrument panel. All the turn signal lights
and the turn signal indicator lights will
flash. To turn off the flasher, push the
button again.
NOTE
When the hazard warning flasher is on,
the turn signals do not work.
Meters and gauges
NOTE
Some of the meters and gauges on the
combination meter use liquid-crystal
displays. You will find their indications
hard to see if you wear polarized
glasses.
&
Speedometer
The speedometer shows the vehicle
speed.
&
Tachometer
The tachometer shows the engine speed
in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the
pointer of the tachometer in the red
zone. In this range, fuel injection will
be cut by the engine control module
to protect the engine from overrev-
ving. The engine will resume run-
ning normally after the engine speed
is reduced below the red zone.
Instruments and controls/Hazard warning flasher
3-8
(151,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
&
Odometer
1)
TRIP RESET switch
2)
Type A combination meter
3)
Type B combination meter
This meter displays the odometer when
the ignition switch is in the “ON” position.
The odometer shows the total distance
that the vehicle has been driven.
NOTE
If you press the TRIP RESET switch
when the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
odometer/trip meter will light up.
The indicators will turn off when:
.
The TRIP RESET switch is not oper-
ated for approximately 10 seconds.
.
The driver’s door is opened and then
closed.
&
Double trip meter
1)
TRIP RESET switch
2)
Type A combination meter
3)
Type B combination meter
This meter displays the two trip meters
when the ignition switch is in the “ON”
position.
The trip meter shows the distance that the
vehicle has been driven since you last set
it to zero.
The display can be switched as shown in
the following sequence by pressing the
TRIP RESET switch.
To set the trip meter to zero, select the A
trip or B trip meter by pressing the TRIP
RESET switch and keep the knob pressed
for more than 2 seconds.
CAUTION
To ensure safety, do not attempt to
change the function of the indicator
during driving, as an accident could
result.
– CONTINUED –
Instruments and controls/Meters and gauges
3-9
3
(152,1)
北米Model "A1340BE-A" EDITED: 2018/ 4/ 2
NOTE
.
If the connection between the com-
bination meter and battery is broken for
any reason such as vehicle mainte-
nance or fuse replacement, the data
recorded on the trip meter will be lost.
.
If you press the TRIP RESET switch
when the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
odometer/trip meter will light up. It is
possible to switch between the A trip
meter and B trip meter indications while
the odometer/trip meter is lit up.
In addition, it is possible to reset the trip
meter by pressing and holding the TRIP
RESET switch.
The indicators will turn off when:
– The TRIP RESET switch is not
operated for approximately 10 sec-
onds.
– The driver’s door is opened and
then closed.
&
Fuel gauge
1)
TRIP RESET switch
2)
Type A combination meter
3)
Type B combination meter
The fuel gauge is displayed when the
ignition is in the “ON” position, and it shows
the approximate amount of fuel remaining
in the tank.
The gauge indication may change slightly
during braking, turning or acceleration due
to fuel level movement in the tank.
NOTE
.
You will see the “
” sign in the fuel
gauge. This indicates that the fuel filler
door (lid) is located on the right side of
the vehicle.
.
If you press the TRIP RESET switch
while the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
fuel gauge will light up and indicate the
amount of fuel remaining in the tank.
The indicators will turn off when:
– The TRIP RESET switch is not
operated for approximately 10 sec-
onds.
– The driver’s door is opened and
then closed.
&
ECO gauge (if equipped)
1)
Type A combination meter
2)
Type B combination meter
The ECO gauge shows the difference
between the current rate of fuel consump-
tion and the average rate of fuel consump-
tion since the trip meter was last reset.
Instruments and controls/Meters and gauges
3-10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст