Subaru Forester (2019). Instruction — part 58
(484,1)
5. Route the wire as shown in the
illustration.
6. Install the light cover on the rear gate.
&
License plate light
1. The license plate lights must be
pushed outwards, and then pulled out to
be removed.
2. Turn the bulb socket counterclockwise
and pull out the socket.
3. Pull the bulb out of the socket.
4. Install a new bulb.
5. Put the bulb socket and the license
plate light cover back in place.
Replacing bulbs
482
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(485,1)
&
Vanity mirror light
CAUTION
Replacing the bulb could cause
burns since the bulb may be very
hot. Have the bulb replaced by your
SUBARU dealer.
&
Door step light
CAUTION
Replacing the bulb could cause a
short circuit. Have the bulb replaced
by your SUBARU dealer.
&
Dome light and cargo area
light
Dome light
Cargo area light (if equipped)
1. Remove the lens by prying the edge of
the lens with a flat-head screwdriver.
2. Pull the bulb out of the socket.
3. Install a new bulb.
4. Put the lens back in place.
&
Other bulbs
It may be difficult to replace the bulbs.
Have the bulbs replaced by your
SUBARU dealer if necessary.
Replacing bulbs
483
11
Maintenance
and
service
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(486,1)
11-25. Replacing key battery
The access key fob/transmitter battery
may be discharged under the following
conditions.
.
The operation of the keyless access
function is unstable.
.
The operating distance of the remote
keyless entry system is unstable.
.
The transmitter does not operate prop-
erly when used within the standard dis-
tance.
Replace the battery with a new one.
&
Safety precautions
CAUTION
.
Do not let dust, oil or water get on
or in the access key fob/transmit-
ter when replacing the battery.
.
Before replacing the battery, re-
move any static electricity.
.
Be careful not to touch or damage
the printed circuit board in the
access key fob/transmitter when
replacing the battery.
.
Be careful not to allow children to
touch the battery and any re-
moved parts; children could
swallow them.
.
There is a danger of an explosion
if the battery is incorrectly re-
placed. Replace only with the
same or equivalent type of the
battery.
.
Batteries should not be exposed
to excessive heat such as bright
sunlight, fire or the like.
NOTE
.
Replace only with the same or
equivalent type of battery recom-
mended by the manufacturer.
.
Dispose of used batteries according
to local laws.
.
Mount the battery in the correct
orientation to prevent fluid leakage.
Be careful not to bend the terminals. It
may result in a malfunction.
.
It is recommended that the battery
be replaced by a SUBARU dealer.
.
Use a new battery.
.
After replacing the battery, confirm
that the transmitter functions properly.
&
Replacing battery of access
key fob
CAUTION
When removing or reinstalling the
access key fob cover, make sure that
the plastic part does not come off or
become misaligned.
Battery: Button battery CR2032 or
equivalent
1)
Release button
2)
Emergency key
1. Take out the emergency key.
Replacing key battery
484
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(487,1)
2. Wrap a flat-head screwdriver with vinyl
tape or a cloth, and insert it in the gap to
remove the cover.
3. Take out the battery using a flat-head
screwdriver with vinyl tape or a cloth.
4. Insert a new battery with its positive (+)
side facing upward as shown in the figure.
5. Attach the cover to the access key fob
by fitting the projections and recesses
together.
&
Replacing transmitter battery
Battery: Button battery CR1620 or
equivalent
1. Wrap a flat-head screwdriver with vinyl
tape or a cloth. Open the key head using a
flat-head screwdriver.
– CONTINUED –
Replacing key battery
485
11
Maintenance
and
service
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(488,1)
2. Remove the transmitter case from the
key head.
3. Open the transmitter case by releasing
the hooks.
1)
Negative (−) side facing up
4. Replace the old battery with a new
battery making sure to install the new
battery with the negative (−) side facing up.
5. Put together the transmitter case by
fitting the hooks on the case.
6. Reinstall the transmitter case in the
key head.
7. Refit the removed half of the key head.
Replacing key battery
486
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(490,1)
12-1. Specifications
These specifications are subject to change without notice.
&
Dimensions
in (mm)
Item
Overall length
182.1 (4,625)
Overall width
71.5 (1,815)
Overall height
68.1 (1,730)*
2
67.5 (1,715)*
3
Wheel base
105.1 (2,670)
Tread
Front
61.6 (1,565)
Rear
61.8 (1,570)
Ground clearance*
1
8.7 (220)
*1: Measured with vehicle empty
*2: Models with roof rails
*3: Models without roof rails
&
Engine
Engine model
FB25
(2.5 L, DOHC, non-turbo)
Engine type
Horizontally opposed, liquid cooled 4 cylinder, 4-stroke direct injection gasoline engine
Displacement cu-in (cc)
152 (2,498)
Bore 6 Stroke in (mm)
3.70 6 3.54 (94.0 6 90.0)
Compression ratio
12.0 : 1
Firing order
1 – 3 – 2 – 4
Specifications
488
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(491,1)
&
Fuel
Fuel requirement
Fuel tank capacity
Unleaded gasoline with 87 AKI (90 RON) or higher
16.6 gal (63 liters, 13.9 Imp gal)
For more details, refer to “Fuel” FP291.
&
Engine oil
For the checking, adding and replacing procedure or other details, refer to “Engine oil” FP450.
NOTE
The procedure for changing the engine oil and oil filter should be performed by a properly-trained expert. It is recommended
that you have this service performed by your SUBARU dealer.
!
Approved engine oil
Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer.
If the approved engine oil is unavailable, use the alternative engine oil described on the next page.
– CONTINUED –
Specifications
489
12
Specifications
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(492,1)
!
Alternative engine oil
If the SUBARU approved oil is unavailable, the following alternative oil can be used.
NOTE
Each quantity indicated here is only a guideline. The necessary quantity for replacement may differ slightly depending on the
temperature and other factors.
Oil grade
SAE viscosity No. and
applicable temperature
Engine oil capacity
API (American Petroleum Insti-
tute) classification SN with the
words “RESOURCE CONSER-
VING”
or
ILSAC (International Lubricant
Specification Advisory Commit-
tee) GF-5, which can be identi-
fied with the ILSAC certification
mark (Starburst mark)
0W-20 synthetic oil is the required oil
for optimum engine performance and
protection. Conventional oil may be
used if synthetic oil is unavailable.
*: If 0W-20 synthetic oil is not available,
5W-30 conventional oil may be used if
replenishment is needed but should be
changed to 0W-20 synthetic oil at the
next oil change.
– Adding the oil from low level to
full level:
1.1 US qt (1.0 liter, 0.9 Imp qt)
– Changing the oil and oil filter:
4.4 US qt (4.2 liters, 3.7 Imp qt)
Specifications
490
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст