Suzuki Grand Vitara JB627. Service manual — part 290
7B-76 Air Conditioning System:
Magnet Clutch Components
S6JB0B7206035
Magnet Clutch Operating Check
S6JB0B7206036
Check the following items.
If any detects are found, repair or replace magnet clutch assembly.
• Inspect armature plate and rotor for signs of oil.
• Check clutch bearings for noise and grease leakage.
• Using an ohmmeter (3), measure resistance of stator coil between clutch lead wire (1) and body ground (2).
If measured resistance is not within tolerance, replace coil.
Specified current of magnet clutch
Approx. 3.8 – 6.0
Ω at 25 °C (77 °F)
2
3
5
6
1
4
4
(a)
I5JB0A720061-01
1. Armature plate bolt
4. Circlip
: 20 N
⋅m (2.0 kgf-m, 14.5 lb-ft)
2. Armature plate
5. Magnet clutch pulley
: Do not reuse.
3. Shim(s)
6. Magnet clutch coil
I5JB0A720063-02
Air Conditioning System: 7B-77
Magnet Clutch Removal and Installation
S6JB0B7206037
Removal
1) Remove compressor from vehicle referring to
“Compressor Assembly Removal and Installation”.
2) Fix armature plate (1) with special tool (A) and
remove armature plate bolt.
Special tool
(A): 09991–06310
NOTE
Do not reuse armature plate bolt.
3) Remove armature plate.
4) Remove shim(s) from shaft.
5) Using special tool (A), remove snap ring (1).
Special tool
(A): 09900–06107
6) Remove magnet clutch pulley (1) with puller (2).
NOTE
Be careful not to damage pulley.
7) Remove snap ring (1) using special tool (B), and
then remove magnet clutch coil (1).
Special tool
(A): 09900–06107
Installation
1) Install magnet clutch coil (3).
NOTE
Protrusion (1) on underside of magnet clutch
coil and hole (2) on compressor body
assembly must match to stop movement of
magnet clutch coil and to locate lead wire
correctly.
1
(A)
2
I5JB0A720071-01
(A)
1
I5JB0A720072-01
1
2
I5JB0A720073-01
(A)
1
I5JB0A720074-02
2
1
3
I5JB0A720075-01
7B-78 Air Conditioning System:
2) Install new snap ring (1) using special tool (A).
Special tool
(B): 09900–06107
3) Install magnet clutch pulley.
a) Set magnet clutch horizontally over clutch
installation boss.
b) Place special tool (B) onto magnet clutch
bearing. Ensure that edge rests only inner rase
of bearing.
Special tool
(B): 09951–15510
c) Install new snap ring (1) using special tool (A).
Special tool
(A): 09900–06107
4) Install armature plate (1).
5) Using special tool (A), tighten new armature plate
bolt (2) to specified torque.
Tightening torque
Armature plate bolt: 21 N·m (2.1 kgf-m, 15.5 lb-
ft)
Special tool
(A): 09991–06310
6) Adjust clearance between armature plate (1) and
magnet clutch pulley by putting shim(s) on
compressor shaft. To measure the clearance,
perform the following steps.
a) Put compressor in a vise.
b) Set dial gauge on magnet clutch plate, and then
adjust its pointer at 0.
c) Connect battery positive terminal (+) to magnet
clutch coil lead wire.
d) Connect battery negative terminal (–) to
compressor body assembly. (At this point,
armature plate and magnet clutch pulley (2) are
kept in contact.)
e) Disconnect battery negative terminal (–) to
compressor body assembly (At this point,
armature plate and magnet clutch pulley (2) are
not in contact.)
f) Read stroke of armature plate from dial gauge by
performing Step d) and e) repeatedly. (Stroke of
armature plate is clearance between armature
plate and magnet clutch pulley (2).)
Standard clearance between armature plate and
magnet clutch
“a”: 0.3 – 0.6 mm (0.012 – 0.024 in.)
7) Install compressor to vehicle referring to
“Compressor Assembly Removal and Installation”.
Relief Valve On-Vehicle Inspection
S6JB0B7206038
Using special tool (A), check if there is refrigerant
leakage.
If there is refrigerant leakage, replace compressor body.
Special tool
(A): 09990–86011
(A)
1
1
I5JB0A720088-04
(B)
I5JB0A720076-02
(A)
1
1
I5JB0A720077-01
1
2
2
1
“a”
I5JB0A720078-02
(A)
I5JB0A720083-01
Air Conditioning System: 7B-79
Specifications
Tightening Torque Specifications
S6JB0B7207001
NOTE
The specified tightening torque is also described in the following.
“Magnet Clutch Components”
Reference:
For the tightening torque of fastener not specified in this section, refer to “Fastener Information in Section 0A”.
Special Tools and Equipment
Recommended Service Material
S6JB0B7208001
NOTE
Required service material is also described in the following.
“Precautions on Servicing Refrigerant Line”
Special Tool
S6JB0B7208002
Fastening part
Tightening torque
Note
N
⋅m
kgf-m
lb-ft
Refrigerant line bolt
12
1.2
9.0
A/C refrigerant pressure sensor
11
1.1
8.0
Compressor mounting bolt
25
2.5
18.0
Armature plate bolt
21
2.1
15.5
Material
SUZUKI recommended product or Specification
Note
Compressor oil
Compressor oil (DH-PS, 250cc)
P/No.: 99000–99022–
00E
09900–06107
09951–15510
Snap ring pliers (opening
type)
Magnet clutch installer
09990–86011
09990–86012
Gas leak detector
Gas leak detector
This kit includes following
items.1. Gas leak detector,
2. Instruction manual, 3.
Filter, 4. Sensor, 5. Dri-sell
battery (size D) )
1
2
3
4
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст