Opel Frontera UBS. Service manual — part 1105
POWER ASSISTED BRAKE SYSTEM 5C – 25
ON-VEHICLE SERVICE
BRAKE HOSE REPLACEMENT
1
2
4
2
3
1
2
4
5
3
Front/Rear Caliper Brake Hose
Removal Steps
1.
Brake pipe
2.
Clip
3.
Bolt and gasket
4.
Hose
Installation Steps
To install, follow the removal steps in the
reverse order.
Rear Axle Brake Hose
Removal Steps
1.
Brake pipe
2.
Clip
3.
Brake pipe
4.
Bolt
5.
Hose
Installation Steps
To install, follow the removal steps in the
reverse order.
5C – 26 POWER ASSISTED BRAKE SYSTEM
REMOVAL
Preparation:
1) Raise the vehicle and support it with suitable
safety stands.
2) Remove wheel and tire assembly.
3) Clean dirt, grease, and other foreign material off
the hose fittings at both ends.
Front/Rear Caliper Brake Hose
1. Brake Pipe
2. Clip
3. Bolt and Gasket
4. Hose
Rear Axle Brake Hose
1. Brake Pipe
2. Clip
3. Brake Pipe
4. Bolt
5. Hose
INSTALLATION
To install, follow the removal steps in the reverse
order, noting the following points. After installing the
brake hoses, bleed brakes as described in this
section.
Front/Rear Caliper Brake Hose
1. Tighten the brake pipes to the specified torque.
Brake Pipe Torque
N·m(kg·m/lb·ft)
16 (1.6 / 12)
2. Tighten the bolt to the specified torque.
Bolt Torque
N·m(kg·m/lb·ft)
35 (3.5 / 26)
NOTE:
•
Always use new copper gaskets.
•
Be sure to put the hooked edge of the flexible
hose end into the anti-rotation cavity.
Rear Axle Brake Hose
1. Tighten the brake pipes to the specified torque.
Brake Pipe Torque
N·m(kg·m/lb·ft)
16 (1.6 / 12)
2. Tighten the bolt to the specified torque.
Bolt Torque
N·m(kg·cm/lb·in)
13 (130 / 113)
POWER ASSISTED BRAKE SYSTEM 5C – 27
BRAKE PIPE REPLACEMENT
1
1
2
Removal Steps
1.
Brake pipe
2.
Plastic clip
Installation Steps
To install, follow the removal steps in the
reverse order.
REMOVAL
Preparation:
1) Raise the vehicle and support it with suitable
safety stands.
2) Remove wheel and tire assembly as necessary.
3) Clean dirt, grease, and other foreign material off
the pipe fittings at both ends.
1. Brake Pipe
2. Plastic Clip
1
Vehice with LSPV
5C – 28 POWER ASSISTED BRAKE SYSTEM
P & B (PROPORTIONING AND BYPASS) VALVE
Master cylinder
(Primary)
Master cylinder
(Secondary)
Rear brake
Front brake
INSTALLATION
To install, follow the removal steps in the reverse
order, noting the following points. After installing the
brake pipes, bleed brakes as described in this section.
1. Tighten the brake pipes to the specified torque.
Brake Pipe Torque
N·m(kg·m/lb·ft)
Master Cylinder Side
Others
12 (1.2/9)
16 (1.6/12)
The P & B valve contains two sections, each serving a
different function.
The proportioning section of the P & B valve
proportions outlet pressure to the rear brakes after a
predetermined rear input pressure has been reached.
This is done to prevent rear wheel lock-up on the
vehicles with light rear wheel loads.
The valve has a By-bass feature which assures full
system pressure to the rear brakes in the event of a
font brake mulfunction, also full front pressure is
retained in the event of rear brake mulfunction.
The P & B valve is not repairable and must be
replaced as a complete assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст