Opel Frontera UBS. Service manual — part 1777
8I–8
SUN ROOF/CONVERTIBLE TOP
7. Remove the cable outer tube(2) fixing screws.
8. Remove the cable outer tube fixing clamps(1) and
guide rail fixing nuts(5).
9. Prying the guide rail a little with a screwdriver, draw
the outer tube out of the grommet(3).
D
At this time, the inner cable(4) remains on the frame
assembly.
10. Remove the sun roof frame assembly.
665RS012
Reassembly
To reassembly, follow the disassembly steps in the
reverse order, noting the following points.
1. When installing the motor or drive unit, set the sun
roof set plate in the full closed position by pushing the
link(3) portion using the screwdriver(2).
2. When installing the sun roof glass(1) to the sun roof
set plate, insert the original shims in the same position
before removing the sun roof glass.
665RS013
SUN ROOF/CONVERTIBLE TOP
8I–9
Sun Roof Drain Hose (Front Side)
Sun Roof Drain Hose (Front Side) and Associated Parts
665RW017
Legend
(1) Clip
(2) Sun Roof Drain Hose
(3) Grommet
(4) Instrument Panel Assembly
(5) Front Inner Liner
(6) Headlining
Removal
1. Disconnect the battery ground cable.
2. Remove the front inner liner.
3. Remove the headlining.
D
Refer to the Headlining in Body Structure section.
4. Remove the instrument panel assembly.
D
Refer to the Instrument Panel Assembly in Body
Structure section.
5. Disconnect the drain hose at the frame complete
side.
6. Apply the soap and water to the body panel grommet.
7. Pass the string from the sun roof frame side through
the drain port side, and remove the drain hose from
the hose fixing clips. Taking care not to allow the body
panel grommet to be removed together with the hose,
pull the drain hose only to the inside of the vehicle.
(The string should be kept as it is.)
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply the soap and water to the body panel grommet.
2. Install the drain hose from inside of the vehicle by
utilizing, as a guide, the string passed during removal
step.
3. The body panel grommet must not be twisted or
caught in during installation.
4. Complete routing, avoiding extreme bends or curves.
5. After routing, install the trim with care not to allow the
drain hose to be caught in.
6. Test the drain condition.
7. The protrusion of drain hose from the body panel
must be within 50 mm (2.0 in). If it exceeds 50 mm
(2.0 in) after correct routing, cut the leading edge so
that the protrusion is within 50 mm (2.0 in).
8I–10
SUN ROOF/CONVERTIBLE TOP
Sun Roof Drain Hose (Rear Side)
Sun Roof Drain Hose (Rear Side) and Associated Parts
665RS015
Legend
(1) Soft Tape
(2) Pipe
(3) Clip
(4) Soft Tape
(5) Sun Roof Drain Hose
(6) Tape
(7) Grommet
(8) Grommet
(9) Clip
(10) Headlining
(11) Rear Fender Inner Liner
Removal
1. Disconnect the battery ground cable.
2. Remove the rear fender inner liner.
3. Remove the headlining.
D
Refer to the Headlining in Body Structure section.
4. Disconnect the drain hose at the frame complete
side.
5. Apply the soap and water to the body panel grommet.
6. Remove the hose fixing tapes and clips.
7. Pull the drain hose to the inside of the vehicle.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply the soap and water to the body panel grommet.
SUN ROOF/CONVERTIBLE TOP
8I–11
2. Insert the drain hose from inside of vehicle, restore
routing, and fix with new soft tape and clip.
If the grommet is removed during removal of drain
hose, insert the grommet into drain hose from outside
of the vehicle, and install on the body panel, avoiding
any twisting.
3. After installing the drain hose, install the trim while
taking care not to crush the drain hose.
Also, care should be taken not to allow the drain hose
connected to the pipe to be caught in.
4. Test the drain condition.
5. The protrusion of the drain hose from the body panel
must be within 50 mm (2.0 in). If it exceeds 50 mm
(2.0 in) after correct routing, cut the leading edge so
that the protrusion is within 50 mm (2.0 in).
Sun Roof Switch
General Description
Sun roof operation can be controlled by pushing
continuously the sun roof switch to activate the sun roof
control unit and sun roof motor.
While the switch is being pushed to the “OPEN” side, the
sun roof stops about 165 mm (6.5 in) before fully open
position. Push the switch again to the “OPEN” side to
open it fully. When the switch is being continuously
pushed to the “CLOSE” side, the sun roof stops about
180 mm (7.1 in) short of the fully closed position and
remains in this state. Push the switch again to the
“CLOSE” side to close it completely.
Removal
1. Disconnect the battery ground cable.
2. Pull down the switch housing(2) and disconnect the
sun roof switch and map light connectors to remove
the sun roof switch(1).
805RS002
Installation
To install, follow the removal steps in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст