Isuzu Rodeo UE. Service manual — part 631
EXTERIOR/INTERIOR TRIM
8J–11
825RW079
Installation
To install, follow the removal steps in the reverse order.
Power Window Motor
Driver Seat Side
Removal
1. Disconnect the battery ground cable.
2. Remove the window regulator assembly (2).
f
Refer to the Window Regulator and Glass removal
steps in Body Structure section.
3. Remove the power window motor (1).
f
Remove three screws.
825RW096
Installation
To install, follow the removal steps in the reverse order.
Front Passenger Seat Side
Removal and Installation
Refer to the Front Window Motor — Driver Seat side
removal and installation steps in this section.
Rear-Left Side
Removal
1. Disconnect the battery ground cable.
2. Remove the rear window regulator assembly (2).
f
Refer to the Rear Window Regulator and Glass
removal steps in Body Structure section.
3. Remove the power window motor (1).
f
Remove three screws.
825RW095
Installation
To install, follow the removal steps in the reverse order.
Rear-Right Side
Removal and Installation
Refer to the Rear Power Window Motor — Left Side
removal and installation steps in this section.
SEAT BELT SYSTEM
9A–1
RODEO
RESTRAINTS
CONTENTS
Seat Belt System
9A
. . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Restraint System (SRS)
9J
. . . . .
Restraint Control System
9J1
. . . . . . . . . . . . . . . . .
SEAT BELT SYSTEM
CONTENTS
Service Precaution
9A–1
. . . . . . . . . . . . . . . . . . . . . .
Front Seat Belt
9A–2
. . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat Belt and Associated Parts
9A–2
. . . .
Removal
9A–2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
9A–2
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Seat Belt
9A–3
. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Seat Belt and Associated Parts
9A–3
. . . . .
Removal
9A–3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
9A–4
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat Buckle Assembly
9A–5
. . . . . . . . . . . . . .
Removal
9A–5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
9A–5
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications
9A–6
. . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
9A–2
SEAT BELT SYSTEM
Front Seat Belt
Front Seat Belt and Associated Parts
760RW040
Legend
(1) Door Seal Finisher (Front & Rear)
(2) Adjustable Shoulder Anchor Assembly
(3) Seat Belt Upper Anchor Bolt
(4) Center Pillar Upper Trim Cover
(5) Front Seat Belt Assembly
(6) Seat Belt Lower Anchor Bolt
(7) Center Pillar Lower Trim Cover
(8) Retractor
(9) Rear Sill Plate
(10) Front Sill Plate
Removal
1. Disconnect the battery ground cable.
2. Remove the sill plate (Front & Rear).
3. Remove the seat belt lower anchor bolt.
4. Remove the center pillar lower trim cover.
5. Remove the door seal finisher (Front & Rear).
6. Remove the center pillar upper trim cover.
7. Remove the seat belt upper anchor bolt.
8. Remove the retractor.
9. Remove the adjustable shoulder anchor assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Tighten the adjustable shoulder anchor assembly
fixing bolts to the specified torque.
Torque: 39 N·m (29 lb ft)
2. Tighten the seat belt anchor bolts (Upper & Lower)
and the retractor fixing bolts to the specified torque.
Torque: 39 N·m (29 lb ft)
SEAT BELT SYSTEM
9A–3
Rear Seat Belt
Rear Seat Belt and Associated Parts
755RW068
Legend
(1) Adjustable Shoulder Anchor Assembly
(2) Seat Belt Upper Anchor Bolt
(3) Slider Plate Trim Assembly
(4) Quarter Trim Cover
(5) Rear Roof Trim Cover
(6) Tailgate Weather Strip
(7) Rear End Floor Trim Cover
(8) Seat Belt Lower Anchor Bolt
(9) Rear Seat Belt Assembly
(10) Retractor
(11) Rear Sill Plate
(12) Rear Door Seal Finisher
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate weather strip.
3. Remove the rear end floor trim cover.
4. Remove the luggage room light.
f
Remove the luggage room light lens (1) and the
fixing screw.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст