Isuzu Rodeo UE. Service manual — part 637
SUPPLEMENTAL RESTRAINT SYSTEM
9J–18
ASSEMBLY UNATTENDED ON A BENCH OR OTHER
SURFACE, ALWAYS FACE THE BAG AND TRIM
COVER UP, AWAY FROM THE SURFACE. THIS IS
NECESSARY SO THAT A FREE SPACE IS PROVIDED
TO ALLOW THE AIR BAG TO EXPAND IN THE
UNLIKELY EVENT OF ACCIDENTAL DEPLOYMENT.
FAILURE TO FOLLOW PROCEDURES COULD
RESULT IN PERSONAL INJURY.
37. Temporarily store the air bag assembly with the air
bag opening facing up, away from the surface upon
which it rests.
Deployed Air Bag Assembly Handling
Put on a pair of shop gloves and safety glasses to protect
your hands and eyes from possible irritation and heat
when handling the deployed air bag assembly.
After the air bag assembly has been deployed, the
surface of the air bag may contain a powdery residue.
This powder consists primarily of cornstarch (used to
lubricate the bag as it inflates) and by products of the
chemical reaction. Sodium hydroxide dust (similar to lye
soap) is produced as a by product of the deployment
reaction. The sodium hydroxide then quickly reacts with
atmospheric moisture and is converted to sodium
carbonate and sodium bicarbonate (baking soda).
Therefore, it is unlikely that sodium hydroxide will be
present after deployment.
Special Tools
WARNING: TO AVOID DEPLOYMENT WHEN
TROUBLESHOOTING THE SRS, DO NOT USE
ELECTRICAL TEST EQUIPMENT SUCH AS A
BATTERY–POWERED OR AC–POWERED
VOLTMETER, OHMMETER, ETC., OR ANY TYPE OF
ELECTRICAL EQUIPMENT OTHER THAN THAT
SPECIFIED IN THIS MANUAL. DO NOT USE A NON
POWERED PROBE–TYPE TESTER. INSTRUCTIONS
IN THIS MANUAL MUST BE FOLLOWED
CAREFULLY, OTHERWISE PERSONAL INJURY MAY
RESULT.
J–41433 SRS Driver/Passenger Load Tool
The SRS Driver/Passenger Load Tool J–41433 is used
only when called for in this section. It is used as a
diagnostic aid and safety device to prevent inadvertent air
bag assembly deployment.
The load tool has four yellow connectors attached to its
case.
The three small connectors are electrically functional and
serve as resistive load substitutions.
No more than two connectors are used at any time. One
of the small connectors is used to substitute for the load of
the driver air bag assembly when it is connected at the top
of the column to the SRS coil assembly. Another small
connector is used to substitute for the load of the driver air
bag assembly and the SRS coil assembly when it is
connected at the base of the column to the SRS wiring
harness. The third small connector is used to substitute
for the load of the passenger air bag assembly when
connected to the passenger air bag assembly harness
connector.
By substituting the resistance of the load tool when called
for, a determination can be made as to whether an inflator
circuit component is causing system malfunction and
which component is causing the malfunction. The load
tool should be used only when specifically called for in the
diagnostic procedures.
901RS146
SUPPLEMENTAL RESTRAINT SYSTEM
9J–19
J–39200 DVM
The J–39200 DVM is the preferred DVM for use in SRS
diagnosis and repair. However, J–34029–A may be used
if J–39200 is not available. No other DVMs are approved
for SRS diagnosis and repair.
901RS153
Scan Tool
The Tech 2 is used to read and clear SRS Diagnostic
Trouble Codes (DTCs). Refer to the Tech 2 Operator’s
Manual for specific information on how to use the Tech 2.
901RW176
J–35616–A Connector Test Adapter Kit
The J–35616–A Connector Test Adapter Kit must be used
whenever a diagnostic procedure requests checking or
probing a terminal. Using the appropriate adapter will
ensure that no damage to the terminal will occur from the
DVM prove, such as spreading or bending. The adapter
will also give an idea of whether contact tension is
sufficient, helping to find an open or intermittent open due
to poor terminal contact.
901RS151
J–42986 SRS Deployment Tool
The J–42986 SRS Deployment Tool must be used for
deployment of the undeployed air bag.
901RW106
SUPPLEMENTAL RESTRAINT SYSTEM
9J–20
J–42987 SRS Adapter For Load Tool
The J–42987 SRS Adapter be used for connect previous
load tool to new SRS system when inspect SRS system
harness.
901RW107
J–41497 SRS Deployment Fixture
The J–41497 SRS Deployment Fixture must be used for
deployment of the undeployed passenger side air bag.
901RW088
SUPPLEMENTAL RESTRAINT SYSTEM
9J–21
Tech 2 Scan Tool
From 1998 RODEO (UE), dealer service departments
are recommended to use Tech 2. Please refer to Tech 2
scan tool user guide.
901RW180
Legend
(1) PCMCIA Card
(2) RS 232 Loop Back Connector
(3) SAE 16/19 Adaptor
(4) DLC Cable
(5) Tech–2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст